MC14106BCPG ON
Gates and Inverters
Description
The MC14106B hex Schmitt Trigger is constructed with MOS P−channel and N−channel enhancement mode devices in a single monolithic structure. These devices find primary use where low power dissipation and/or high noise immunity is desired. The MC14106B may be used in place of the MC14069UB hex inverter for enhanced noise immunity or to “square up” slowly changing waveforms.This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high−impedance circuit. For proper operation, Vin and Vout should be constrained to the range VSS ≤(Vin or Vout) ≤ VDD.Unused inputs must always be tied to an appropriate logic voltage level (e.g., either VSS or VDD). Unused outputs must be left open.
- Electrical & Electronic Components
- Pdip
- Ttl Loads
- Pb−free Packages
Product characteristics
- Kynix Part #
- KY32-MC14106BCPG
- Manufacturer Part #
- MC14106BCPG
- Product Category
- Gates and Inverters
- Manufacturer
- ON Semiconductor
- Description
- Inverter Through Hole -55°C ~ 125°C Tube 1μA 4000B 14-PDIP
- Package
- DIP-14
- Quantity
- On Order
- Lead Free Status / RoHS Status
- Lead free / RoHS Compliant
- Lead Time
- Send email to learn lead time
Similar products from KYNIX SEMICONDUCTOR HONG KONG LIMITED
KYNIX SEMICONDUCTOR HONG KONG LIMITED
Hong Kong
The TI Gates and Inverters SN74LVC1G08DRLR is a single-gate AND gate surface mount device designed for use in a wide range of applications. This device is capable of operating over a temperature range of -40°C to 125°C and is available in a Digi-Reel alternate packaging. It features a low power consumption of 10μA and is powered by a 5.5 V supply voltage. The device is housed in a SOT-5 package and is ideal for use in low-power applications. It is also suitable for use in automotive, industrial, and consumer applications. The device is designed to provide reliable performance and is backed by TI's quality assurance.
KYNIX SEMICONDUCTOR HONG KONG LIMITED
Hong Kong
The AT27C256R-45PU is an IC EPROM (erasable programmable read-only memory) from Atmel. It is a 256K parallel 28-pin DIP (dual in-line package) memory IC. This device is ideal for applications that require a large amount of non-volatile memory. It is capable of storing up to 32,768 bytes of data and can be programmed and erased in-circuit. The device is also capable of withstanding up to 100,000 erase/write cycles. It has a wide operating temperature range of -40°C to +85°C and is available in a variety of packages. The AT27C256R-45PU is a reliable and cost-effective solution for applications that require a large amount of non-volatile memory.
KYNIX SEMICONDUCTOR HONG KONG LIMITED
Hong Kong
The Microchip Technology Inc. 24CXX, 24LCXX, 24AAXX and 24FCXX (24XX*) devices are a family of 128-bit through 512 Kbit Electrically Erased PROMs. The devices are organized in blocks of x8-bit memory with 2-wire serial interfaces. Low-voltage design permits operation down to 1.7V (for 24AAXX devices), with standby and active currents of only 1 μA and 1 mA, respectively. Devices 1 Kbit and larger have page write capability. Parts having functional address lines allow connection of up to 8 devices on the same bus. The 24XX family is available in the standard 8-pin PDIP, surface mount SOIC, TSSOP and MSOP pack ages. Most 128-bit through 16 Kbit devices are also available in the 5-lead SOT-23 package. DFN packages (2x3mm or 5x6mm) are also available. All packages are Pb-free (Matte Tin) finish. Features: • 128-bit through 512 Kbit devices • Single supply with operation down to 1.7V for 24AAXX devices • Low-power CMOS
KYNIX SEMICONDUCTOR HONG KONG LIMITED
Hong Kong
The Intersil ISL317XE are ±15kV IEC61000 ESD Protected, 3.3V powered, single transceivers that meet both the RS-485 and RS-422 standards for balanced communication. These devices have very low bus currents (+125μA/-100μA), so they present a true “1/8 unit load” to the RS-485 bus. This allows up to 256 transceivers on the network without violating the RS-485 specification’s 32 unit load maximum, and without using repeaters. For example, in a remote utility meter reading system, individual meter readings are routed to a concentrator via an RS-485 network, so the high allowed node count minimizes the number of repeaters required.