Germany
Manufacturer/ Producer
Germany
Technical information When machining bar material particular care should be taken that as little material as possible is removed as cutting forces should be minimised and costs reduced. Therefore the exchangeable disc should be selected as a function of the work-piece which is to be parted. Tool systems Das RC-System und S-System sollte als erste Wahl bei den Abstechbearbeitungen verwendet werden. Die Schneidplatten wurden so gestaltet, damit der Span schmäler als die abzustechende Nut ist und ein optimaler Spanablauf gewährleistet werden kann. Das Z-CUT-DUO System ist bedingt durch die Doppelschneidplatte auf eine bestimmte Stechtiefe begrenzt.
Request for a quoteGermany
Technical information Axial grooving is among the most technically difficult machining process in the whole field of metal removal. In this process the chip, once removed, must overcome not just the shaping of the material but also the circular movement. It is particularly important that the machining should always commence at the outer diameter of the axial groove as tool stability is in direct proportion to the diameter. It is preferable for the tool to be used underneath the work-piece so that the chips can fall downwards without obstruction. Tool systems The S System is a modular tool system which offers innumerable possibilities to the user. The cutting tips for this system are ground to a sharp edge and produce an excellent surface quality. It goes without saying that the cutting tips can be supplied with all required corner radii. The RC System is screw clamped; the cutting tip is securely clamped into position so that it cannot fall out. When rough turning, grooving depths of up to 100 mm are standard. When turning larger diameters we are also able to achieve grooving depths of 150 mm.
Request for a quoteGermany
Technical information By using our internal grooving system it is possible to machine grooves on hole diameters starting from 2 mm. Tool systems With the proven TURN-CUT 2 cutting system you can machine grooves and longitudinally turn hole diameters starting with hole diameters of 16.5mm. When using A Series tools, grooving and longitudinally turning is possible on hole diameters starting from 2 mm.
Request for a quoteGermany
Customised cutting tips are usually necessary for profile cutting. We have already custom-manufactured several thousand shapes for customers – and with short delivery times.
Request for a quoteGermany
The short cutting systems in our sales programme cover all cutting tasks in this area.
Request for a quoteGermany
Machining non-ferrous metals is really only different from the normal machining of steel by the use of special cutting tips and coatings.
Request for a quoteGermany
When turning outside diameters, it is necessary to consider which clamping system should be used and which components will be made most often. This is because if larger components are to be turned (and therefore with correspondingly greater depths of cut) a different system must be used than when turning smaller components with a finishing pass. Determining the cutting direction and tool holder A turning tool which works from right to left is called a right-hand turning tool because it machines the right-hand side of the work-piece (when looking at the tool point, the main cutting edge of the turning tool is on the right). View of internal and external turning Clamping systems The C Clamping System, P Clamping System, the M and S Clamping Systems. ISO Key image
Request for a quoteGermany
In face turning the tool moves vertically to the axis of the work-piece. When rough machining, a tool movement from the outside of the work-piece to the inside is preferred; in finish machining, the preferred movement is from the inside to the outside. The largest possible corner radius should be chosen in order to ensure optimal tool stability and cost-effectiveness.
Request for a quoteGermany
Contrary to external turning, tool selection and tool use are of greater significance in internal turning as these are limited by the length and hole diameter of the work-piece. During internal turning it is very important to select a boring bar which is optimal for the hole diameter in order to minimise vibrations. Zinner tools are available in steel, heavy metal or hard metal shanks.
Request for a quoteGermany
Complex machining processes can now be completed with fewer tools as a result of the use of profile turning tools (also called turning-milling tools). The use of profile turning tools enables the number of tool positions in the tool changer to be reduced.
Request for a quoteManufacturer/ Producer
Karl-Martell-Strasse 35
90431 Nürnberg - Germany
Italy
Our drill bits for tire mold cleaning are high speed steel cobalt (Hss/Co) and have undergone a special heating process that makes them specifically suitable for the drilling and cleaning of vent holes in both steel and aluminium tire molds. Diameter range: 0.4 mm – 3.0 mm (for side walls drilling and agro tire molds); Helix range: 10 mm – 350 mm (tire mold deep drilling); Length range: 40 mm – 400 mm (extra long drills); Standard or Parabolic helix geometry.
Request for a quoteGermany
Efficient, easy-cutting diamond core bit especially for reinforced concrete and concrete. Suitable for core drill rig and freehand use.
Request for a quoteGermany
Efficient, easy-cutting diamond core bit especially for reinforced concrete and concrete.
Request for a quoteGermany
Plastic drill cassettes for drill bit sets (HSS drill sets DIN 338, machine tap sets DIN 371/376 etc.) Four parts: cover, base, insert and safety pin Sturdy and modern design with ergonomic body design Clear cover allows for product visibility
Request for a quoteCreate one request and get multiple quotes form verified suppliers.