Pneumatic systems and tools - Import export

Our H guides can be adapted to many electric actuators of the market (with threaded rod or tapped rod). Also available in anticorroding version (AluStainless Steel)

These linear guide bearings are available in cylindrical short housings or prismatic long housings. Guided on ball bushings, bronze or polymer bearings. The housing is in anodized aluminium. To build your own linear guide These linear guide bearings make it possible to create a guide unit adapted to your needs and integrated into your machine You choose the diameter of the guide rods according to load capacity and rigidity, the type of guidance (bronze, polymer, ball bushings), the guide length (long prismatic or short cylindrical bearings) and the rods spacing according to the application. You can integrate any cylinder (type, standard, brand …) by using a cylinder rod coupling. You limit the number of parts by directly using a support of your frame and your end plate. A range of stainless steel guide bearings is also available Guide Type 34X You can also use bearing blocks

Pneumatic gripper with 2 or 3 concentric fingers Single acting with rear central air connection High clamping force External clamping and vertical using only Without detection Screwing gripper technology The technology of this gripper allows it to develop a very large clamping force (about 10x the force of a gripper) so as to obtain the necessary tightening torque in the following applications – screwing cosmetic or hygiene bottles, with or without spout – screwing of pots or cans with torque control – screwing of thermostatic subassemblies – screwing push buttons The central rear pneumatic supply and single acting makes it easy to mount on a rotating joint. Screwing bottles with pump spoutThe wide angle opening version is generally used for screwing vials with pump spouts. The 2finger version makes it possible to tighten square or prismatic caps, but also to reduce cycle time by let go the bottle radially by opening the gripper at the height of clamping

Pneumatic parallel gripper with 2 concentric fingers and long opening stroke. Very long prismatic guide for torsional torque resistance. Exceptional length/stroke ratio Interest of longstroke parallel grippers These pneumatic parallel grippers with long opening stroke can seize parts with very different sizes (example a range of bearings, a range of wheels …). The length of the sliders makes it possible to support fairly long jaws without the risk of buttressing. Exceptional length/stroke ratio and robustness The clamping force and guiding quality are constant throughout the stroke. The slides being mounted in parallel, these grippers have a very good stroke/length ratio. With a hard anodized body, a long prismatic steel guide, these parallel pneumatic grippers are reliable and robust. Mounting interfaces allow them to be integrated into a pneumatic handling assembly.

Handling pneumatic gripper with parallel clamping with 3 concentric fingers. The guide is prismatic and mechanism is completely protected Benefits of 3finger parallel tightening Although most handling applications are using parallel grippers with 2 fingers, because even in the case of cylindrical parts, Vshaped jaws allow a good grip. The use of a gripper with 3 fingers is preferred in 2 case – refocusing of the part along 2 axes during tightening – stability of a long cylindrical part clamped by its end In the particular case of screwing, we have a range of 3jaw grippers specifically dedicated to screwing Type 2913 grippers. Reliability and robustness of Type 24 parallel grippers With a hard anodized body and cylinder, prismatic steel guide, fully protected mechanism, these pneumatic parallel grippers are robust and reliable. The positions are detected by magnetic detectors (delivered separately) thanks to 2 Tgrooves on the upper face of the cylinder.

Pneumatic gripper with 2 concentric fingers Finger selflocking closed gripper (toggle joint action) Elastic absorption at opening Interest of 180 ° angle grippers Grippers with 180° opening angle are generally used to suppress a clearance movement because the open fingers allow the product to pass laterally, for example during a linear transfer or for maintaining a product on a turntable. Selflocking on closing by toggle effect These grippers use toggle technology that allows selflocking of the jaws in the last degree of closure and a large clamping force. They therefore remain locked even in the absence of air pressure. They can only be used for a grip from outside the piece and for parts with an identical grip dimension. The detection cam mounted on the axis of rotation allows the 2 inductive sensors to detect any desired position. The option « opening screw limitation » allows to adjust the opening stroke if the 180 ° are not sought

Motorization by integrated pneumatic cylinder Driving by rack and pinion system Adjustable mechanical stops Hydraulic shock absorbers Inductive sensors The wrist of a manipulator arm These rotary modules are, for example, the wrist of a manipulator arm, the turner of parts on a conveyor or the axis of rotation of an oscillating manipulator. In general, they rotate the gripper that grips the part. These modules are equipped with hydraulic dampers and inductive sensors, the rotation guidance is ensured by 2 ball bearings that allow this module to be used in all directions, even with offcentered payload. Rotary cylinder without angular play at end of stroke The end stops located under the plate allow there to be no shock in the rack and pinion transmission and no angular play at the end of the stroke. The absence of angular play allows use in assembly or precise positioning applications with 2 positions and the absence of impact in rack

Guides, delivered without motor, allows to realize systems with 1, 2 or 3 axes For LinMot® motors P0123, P0137, P0148 Stainless steel version for *SSC motors Presentation of the range of guides for LinMot® motors These guides are intended exclusively for cylindrical linear motors of the LinMot® brand and are broken down into 5 families LB modules for pick and place manipulators LE modules Gantry LR LH guide units comparable to guide units for pneumatic cylinders Guides in stainless steel LX and LW for motors * SSC Special features of the LE and LB modules On LE modules, for vertical applications, it’s possible to have a mechanicalpneumatic brake or a LinMot MagSpring. The LB23 module is equipped with pneumatic balancing (antifall in the event of a power outage but also for high speed by eliminating the impact of gravity).

For electric cylinders ISO 15552 size 32 to 100 Selfcentering rod coupling without axial play adapted to positioning Principle of rod coupling with reduced axial play Rod coupling with adjustable axial playThe difference with the ISO 15552 pneumatic cylinder guide units is at the level of the cylinder rod coupling on these guides for electric cylinders, the selfaligning rod coupling has no axial play (or a reduced axial play) depending on the assembly carried out, these units without axial play are therefore suitable for positioning applications. For applications without positioning accuracy or with high radial loads in static, it’s possible to use the guide units for pneumatic cylinders with a guide on plain bearings, since the rod coupling has an axial play (<0,2 mm). Guides for nonISO actuators For electric actuators which are not ISO, we know how to adapt our guide units to most of the rod actuators on the market see Hguide for actuators.

Pneumatic retractable stop Locking by toggle joint action Adjustable stop screw Operating principle of the retractable stop This retractable stop is drived by a doubleacting pneumatic cylinder. It is retracted by a 90 ° rotation of the finger. When it is engaged to stop the moving element, it is mechanically locked by a toggle joint action. The retractable finger supports an impact force of 2250 N or less, it is generally necessary to provide damping at the point of contact (elastic or hydraulic depending on the application). Detection by 2 inductive Ø8 detectors is optional. Using of the retractable pneumatic stop There are 3 common applications for this retractable stop • Create an intermediate position for a manipulator or a linear pneumatic gantry • Create a conveyor stop • Referencing a product on a workstation For an intermediate position of the pneumatic manipulator, a hydraulic shock absorber must be placed opposite the stop screw.

The Modular Tooling Systems for Transfer Presses consist of arms and pneumatic clamps, these clamps allow the gripping of the sheet metal pieces for their movement to the subsequent work phases. It is also possible to use compensation slides or groups of actuators to realize auxiliary movements on the transfer lines. A simple design, a fast assembly and a rapid development can be achieved by using modular components, such as terminals of various types, extensions, joints and regulation elements. Two types of Brackets can be used for the junctions. The first type consists of friction brackets with open rings that are tightened by appropriate screws. These brackets can move along a tube, hence, the adjustment of the position can be done either along the axis of the tube or angularly. The second type of bracket consists of gear brackets that can fit any requirement thanks to an Exclusive Modular System. With only 8 pieces it is possible to reach unlimited combinations.