• europages
  • >
  • COMPANIES - SUPPLIERS - SERVICE PROVIDERS
  • >
  • screws

Results for

Screws - Import export

France

Verified by Europages

Material: Aluminium. Version: Bright. Flat seal asbestos-free. On request: Cap marked OIL. Drawing reference: 1) flat seal

Request for a quote

France

Verified by Europages

Also called fixture clamps. The minimal height of this fixture clamp allows numerous clamping problems in fixture and equipment construction to be solved. The brass hex washer offers a gentle yet extremely stable and safe clamping of workpieces. By using several fixture clamps entire pallets can be set-up. “A” = distance from workpiece to screw centre (cam screw). On request: Replacement cam screws.

Request for a quote

France

Verified by Europages

The double-sided clamp straps are ideal for series clamping. For special applications, the clamping flange can be replaced with another clamping flange by loosening the clamping screw. The clamping flange must always have a contact point on both sides. Functional principle: 1. Use a hand-held or electric tool to tighten the hexagon head bolt (make sure that the maximum tightening torque is not exceeded). When clamping, the clamping flange automatically turns by quarter of a rotation and starts the clamping stroke. 2. Use reverse procedure to loosen the hexagon head bolt. The clamping flange automatically returns to its starting position (the set screw can be used to change the position of the clamping flange). Drawing reference: 1) Hexagon head bolt 2) Slotted round nut 3) Set screw

Request for a quote

France

Verified by Europages

Slide hammer tempered and chromed. Shaft, stop and guide sleeve hardened and chromed. Note: These extractors are used to remove locating pins and centring pins (03105, 03106, 03107, 03108, 03325) with M3 - M8 tapped holes. Drawing reference: 1) stop 2) slide hammer 3) shaft 4) cross pin 5) lock screw 6) guide sleeve 7) cap screw 8) 1 set guide sleeves

Request for a quote

France

Verified by Europages

Case-hardened, black oxidised and ground. Note: To align fixtures and clamping elements on subplates and palettes with location holes. They can be mounted in holes or slots.

Request for a quote

France

Verified by Europages

The mandrel collet is used in small through bores to position and clamp workpieces. Clamping is carried out manually from above using a hex key. The mandrel diameter can be ground to suit the application. The bore for the mandrel should have an H7 tolerance. D min = smallest permissible diameter to which D can be ground. applicable for holes from Ø5 to Ø12.5 mm compact design, small installation space simple handling mounting in any position different installation types possible surface pressure protects the workpiece surface individually adaptable to the diameter Technical data: The tightening torque max. Nm given in the table refers to the spanner size AF2. Assembly: If required, diameter D can be adapted to suit the diameter being held. To do this, expand the mandrel collet ca. 0.2 mm over the required diameter. Grind the OD of the mandrel collet to suit the ID of the workpiece bore.

Request for a quote

France

Verified by Europages

When the positioning cone and bush are mated, the balls are pressed together within the rubbers elastic range and thus locate the two parts in which they have been fitted, with maximum accuracy. To ensure that the rubber in which the balls are embedded is deformed within the elastic range, one must merely ensure that the depth of the hole into which the positioning bush is later pressed is precisely observed. The positioning cone is supplied ready to fit into the positioning bush and must simply be fitted into the counterpart component. Henceforth, a precise zero point positioning system is in place.

Request for a quote

France

Verified by Europages

France

Verified by Europages

Case-hardened. Toleranced diameter ground. Note: These centring pins are suitable for the central holes of our workholding elements 01148, 01263, 01265, 01267 and 01850.

Request for a quote

France

Verified by Europages

Ball end locating pins are specially designed to ease the locating process. The tendency to jam, caused by the locating hole not being at right angles to the pin or by the pushing force not being parallel to the pin axis, is minimized by the ball-end form (see illustration).

Request for a quote

France

Verified by Europages

Hardened and ground (HRC 56 +2). Note: The locating pins can be easily removed with an extractor.

Request for a quote

France

Verified by Europages

The indexing and clamping grips enable the positioning, securing and clamping of diverse positioning elements with just one product. Indexing is carried out using the indexing pin and the item is clamped using the end face of the sleeve. A protruding signal button means that the indexing pin is not completely extended.

Request for a quote

France

Verified by Europages

Cam-action indexing plungers are used when the indexing pin should not project all the time. Turning the handle through 180° retracts the pin. A notch ensures that the handle remains in this position.

Request for a quote

France

Verified by Europages

Indexing plungers are used where it is necessary to prevent changes of position due to lateral forces. A new locking position can be set only after the plunger has been manually disengaged. With this indexing plunger a cam lever is used to retract the pin. The indexing plunger remains unlocked as long as the handle is positioned over the dead-centre of the cam. The ergonomic cam lever enables light handling with low effort. Temperature range: Permanent operating temperature acc. to IEC 216 max. 160°C. Short-term operating temperature max. 250°C. Advantages: Simple and quick operation. Suitable for high temperature applications. With integrated detent function. On request: Special versions. Accessory: Spacer rings 03089 Positioning bushes for indexing plunger 03099-50 Mounting brackets 03099

Request for a quote

France

Verified by Europages

Indexing plungers are used to prevent any change in locking position due to lateral forces. A new locking position can only be set after the pin has been manually disengaged. Form C or D is recommended for applications in which the pin is disengaged over extended periods and should be prevented from springing back.

Request for a quote

France

Verified by Europages

Stainless steel version Indexing pin not hardened: Threaded sleeve 1.4305. Indexing pin 1.4305. Mushroom knob black-grey thermoplastic. Version: Steel version: Indexing pin hardened, ground, black oxidised. Stainless steel version: Indexing pin not hardened, ground, bright. Note: Indexing plungers are used to prevent any change in position due to lateral forces. A new locking position can only be set after the pin has been manually disengaged. Form C or D is recommended for applications in which the pin is disengaged over extended periods and should be prevented from springing back.

Request for a quote

France

Verified by Europages

Indexing pin hardened: Threaded sleeve and indexing pin free-cutting steel Stainless steel version: Indexing pin hardened: Threaded sleeve 1.4305 Indexing pin 1.4034. Mushroom knob black grey thermoplastic. Thread lock blue polyamide. Version: Steel version: indexing pin hardened, ground and black oxidised. Stainless steel version: indexing pin hardened, ground and bright. Note: Indexing plungers are used to prevent any change in locking position due to lateral forces. A new locking position can only be set after the pin has been manually disengaged. Form CP is recommended for applications where the plunger remains disengaged over a long period and the pin should be prevented from springing back. The thread lock enables the plunger to be screwed in to the exact depth required, no spacer ring is required. The thread lock is a gripping polyamide coating that is applied punctiform (spot).

Request for a quote

Do you sell or make similar products?

Sign up to europages and have your products listed

Add my business

France

Verified by Europages

These bushes are ideal for easy and quick positioning of ball lock pins and locking pins. Advantages: centred by the centring collar. easy and reliable installation. can be screwed into various materials. usable both sides

Request for a quote

France

Verified by Europages

Clamping joint high-tensile aluminium. Hinge pin, support plate and stop bar, steel. Version: Clamping joint anodised blue and black. Hinge pins, support plate and stop bar black oxidised. Note: The 5D-swivelling stop serves, among other things, as a versatile instrument for positioning on machining tools or for assembly work. It is infinitely adjustable, quickly and flexibly in 5 axes. Supplied complete with M8x12 T-slot nut and hex key. On request: Connecting element for combining several 5D-swivelling stops.

Request for a quote

France

Verified by Europages

Body and set screw carbon steel. Version: Body black oxidised. Set screw tempered and black oxidised. Note: The adjustable stops have three tapped holes to accept the set screws.

Request for a quote

France

Verified by Europages

Body aluminium. Other metal components steel. Plastic components PA6. Version: Body natural tone anodised. Other metal components trivalent blue passivated. Note: Sliding stop for profile systems type B, type I, and DIN 650 T-slots. Locked by turning the star grip. Sprung threaded pin ensures smooth sliding without tilting the slot key when loosened.

Request for a quote

France

Verified by Europages

Black. Pan head screw and retaining plate electro zinc-plated. Note: Magnetic catch for swing and sliding doors. The elongated holes enable flexible positioning on aluminium profiles and panel elements. Drawing reference: 1) Pan head screw 2) Retaining plate

Request for a quote

France

Verified by Europages

Quick catch for various applications such as holding doors, hatches, screens etc. closed. The double ball catch consists of a housing and a latch bracket that engages between the two balls. The latch bracket can engage from the front or the side. The engagement pressure is adjustable. Drawing reference: 1) counterbore DIN 74-A

Request for a quote

France

Verified by Europages

Sleeve and spring stainless steel. Ball stainless steel or POM. Version: Sleeve bright. Steel ball hardened and bright.

Request for a quote

France

Verified by Europages

These spring plungers are chiefly used as ejectors and spring stops in machine construction. The thrust pin is actuated in the axial direction. Drawing reference: 1) grub screw glued in

Request for a quote

France

Verified by Europages

Sleeve steel grade 5.8. Thrust pin POM. Spring grade D steel wire.

Request for a quote

France

Verified by Europages

Sleeve 1.4305. Thrust pin 1.4034. Spring 1.4310. Version: Bright. Thrust pin hardened.

Request for a quote

France

Verified by Europages

Sleeve 1.4305. Ball 1.4034. Spring 1.4310. LONG-LOK thread lock, Nylon.

Request for a quote

France

Verified by Europages

The combination of excellent material properties is a special feature of silicon nitride (Si3N4). These include high resiliance and stability, excellent wear properties and good chemical resistance.

Request for a quote

Request for quotes

Create one request and get multiple quotes form verified suppliers.

  • Only relevant suppliers
  • Data privacy compliant
  • 100% free