Polypropylene seals - Import export

PNEUMATIC SEALER CP 500 Electropneumatic sealer with double sealing impulse bar with (the resistance heat for a few seconds) suitable for closing packaging polyethylene, PVC and polypropylene, coupled aluminum, etc. It has four positions of voltage to the sealing bar, timer for adjusting the welding time and timer for the cooling time. The double sealing bar (top and bottom) welded from 3 mm allows the closing of envelopes very thick, laminated bags and bellows. The closing of the bars takes place by a pneumatic cylinder unit with pressure and pedal control. Maximum thickness weldable 0.25 mm. The CP 500 can be easily oriented from 0 to 90 degrees.

Impulse sealers MG 820 series, with 820 mm sealing bar and suitable for sealing polyethylene, pvc and polypropylene bags. They have a special timer for adjusting the sealing time based on the thickness and type of material. The MG sealers are complete with a manual cutting unit for the trimming of the sealed bags and/or the creation of bags from tubular reels (if the machine is equipped with a roll holder). The sealers bars must be closed manually by the operator and are automatically held by a magnet until the end of the cycle. There are special supports with mechanical pedal, for the manual sealing machine and with electric pedal for the sealing machine with motorized bar closing. Available models: MG 820: bench sealing machine with manual closing of the bars MGMI 820: bench sealing machine with motorized bar closing and electric pedal

MG 421 SEALING MACHINE WITH CLOSING MAGNET Impulse sealers MG 421 series with 420 mm sealing bar and suitable for sealing polyethylene pvc and polypropylene bags. They have a special timer for adjusting the sealing time based on the thickness and type of material. The MG sealers are complete with a manual cutting unit for the trimming of the sealed bags and/or the creation of bags from tubular reels (if the machine is equipped with a roll holder). The sealing bars must be closed manually by the operator and are automatically held by a magnet until the end of the cycle. They can be equipped with special supports with mechanical pedal, for the manual sealing machine and with electric pedal for the sealing machine with motorized closing of the bars. The MG 421 series sealing machines are available with bars with mechanical or motorized closure with a sealing thickness of 3 or 5 mm depending on the model. There are also special models in stainless steel and with 2 parallel welds of 3 mm.

Product information "Cross bottom bag made of OPP with sealed seam, highly transparent, 30-40µ in different sizes" Cross bottom bag made of OPP with sealed seam, highly transparent, 30-40µ, in different sizes Features: highly transparent material OPP (polypropylene) sealed seam thickness 0.03mm (30µ) Material: This high quality and food grade cross bottom bag is made of OPP, stable and highly transparent. Our cross-bottom bags made of polypropylene have a sealed seam welded on the back and are perfect for filling flavored, ground products such as salt, spices, decorative sand, etc. or confectionery.

Product information "Block bottom bag made of OPP with sealed seam, highly transparent, 40-50µ, in different sizes" Block bottom bag made of OPP with sealed seam, highly transparent, in different sizes Features: highly transparent Material OPP (polypropylene) Sealed seam thickness 0.04mm (40µ) Material: This block bottom bag is made of OPP with sealing seam (highly transparent), stable and odorless. Block bottom bags provide protection from air and moisture. Our block bottom bags form a standing surface when unfolded and stand firm even without contents. They are particularly suitable for filling flavored, ground products such as salt, spices, decorative sand, etc. The plastic film ensures long and dry storage and the flavor is retained.

Product information "Block bottom bag made of OPP with sealed seam, highly transparent, 40-50µ, in different sizes" Block bottom bag made of OPP with sealed seam, highly transparent, in different sizes Features: highly transparent Material OPP (polypropylene) Sealed seam thickness 0.04mm (40µ) Material: This block bottom bag is made of OPP with sealing seam (highly transparent), stable and odorless. Block bottom bags provide protection from air and moisture. Our block bottom bags form a standing surface when unfolded and stand firm even without contents. They are particularly suitable for filling flavored, ground products such as salt, spices, decorative sand, etc. The plastic film ensures long and dry storage and the flavor is retained.

ME-CFE CONSTANT AUTO SEALERS WITH MOTOR CONTROL Table top motorized sealer with electric pedal and welding bars at a constant temperature for sealing polypropylene bags and paired/laminated aluminium, paper, barrier materials, etc. The sealing bars of the type "hot bar" are equipped with resistance and thermostat for controlling the temperature from 30 ° C to 250 ° C. The closure of the bars it takes place through an engine which guarantees a high welding pressure (0,7 Kg./cm2) and allows the sealing of envelopes with hight tickness with or without side bellows. Operation The operation provides for the closure of bars and seals the bag following operator control, by electric pedal. This allows the operator to grab the bag with both hands, being able to perform a more precise sealing and parallel to the bag.

Model P329S with lithium ion (Li-Ion) 18V battery and reinforced motor for maximum autonomy (up to 450 strapping with a charge), the maximum tensile strength (up to 4000 N) and the reliability of the weld. The ease of insertion of the strap makes it very quick and simple to use. The independent settings of all parameters ensure optimum performance and maximum seal with polypropylene and polyester strapping of any size and quality.

New model P328/P328S with lithium ion (Li-Ion) 18V battery and reinforced motor for maximum autonomy (up to 600 strapping with a charge), the maximum tensile strength (up to 2400 N) and the reliability of the weld. The ease of insertion of the strap makes it very quick and simple to use. The independent settings of all parameters ensure optimum performance and maximum seal with polypropylene and polyester strapping of any size and quality.

The patented bag closing system “Over Tape Bag Sealer” from STATEC BINDER seals woven polypropylene (PP) bags airtight. A woven PP tape is used for a reliable and secure closure. If necessary, the bags can also be sewn. Both pillow bags and gusset bags can be securely closed. This sealing technology facilitates the handling of dusty and odour-intensive products of the food and feed industry. During operation, the filled bags are transported to and from the bag closing system via a conveyor belt. A sensor detects the position of the bag and automatically puts it into the trimming area. After cutting the top edge of the bag a woven PP tape is applied over the open edge of the bag to seal it with hot air. The hot air to seal the bag airtight and odourless is produced by a heating unit in the machine.

This special automatic table top/vertical with stand constant heat sealer. Are suitable for sealing polypropylene and paired / laminated bags, paper, barrier materials, etc. The sealing jaws of the type "hot bar" are equipped with resistance and thermoregulator for controlling the temperature from 30 ° C to 200 ° C. The closing of the jaws is through an electromagnet which ensures a high sealing pressure and allows the sealing of thick bags with or without side gussets. Operation The operation provides for the closure of bars and seals the bag following operator control, by electric pedal. This allows the operator to grab the bag with both hands, being able to perform a more precise sealing and parallel to the bag. The vertical model with pedestal can be tilted to 90 degrees, has a special support surface to support the bag during sealing. In this way the operator has both hands free to hold the bag since the sealing is made by pressing the pedal.

ME-FDE SEALERS WITH DOUBLE MOTORIZED PULSE SEALING BAR AND TEMPERATURE CONTROL The new bench sealers with double impulse sealing bar and temperature control, allow the optimal sealing of any type of envelopes and sealable bags. The high pressure exerted by the motorized descent of the bars (0.7 Kg./cm2) allows perfect sealing even on very thick materials. The double active motorized sealing bar (heats above and below) and the 5 mm sealing they allow the closure of envelopes with high thickness, laminated and envelopes with bellows. In addition to sealing polyethylene, polypropylene, coupled paper, aluminum, pvc and medical bags, it also allows the sealing of advertising banners. To seal the banners, we recommend sending samples, without obligation, to carry out the sealing tests. Maximum sealable thickness 0.20 mm (0.40 tot). Timers for regulating the sealing and cooling temperature ensure maximum reliability on all types of material.

Continuous band sealer suitable for closing horizontal bags with a maximum height mm. 400 and max weight. 5 kg. By using PTFE seal belts, polyethylene, polypropylene, cellophane, paper, aluminum, and other laminates can be sealed. The temperature is controlled by an electronic controller and the speed is adjustable. The distance between the solder and the edge of the bag is 20 mm. The distance (width) between the welding headand the conveyor belt is adjustable and is also adjusted the height of the conveyor belt to the plane of welding. The machine is equipped with a marker rotary heat and interchangeable characters (20 charactersmax height 5 mm.), The system works with inked rollers for easy reading and comes complete withphotocell to make a mark at the desired point.

Heat-sealing roller FP802/803 with constant heat which allows the sealing of bags and heat-sealable materials. This roller allows you to make seals with different shapes (square, circular, etc.) according to your needs. Once the roller has been switched on, the operator must wait for the roller to warm up for about 10 minutes. The temperature is adjustable via a potentiometer and reaches a maximum of 200 ° C. There is no graduated scale. The temperature must therefore be set following practical tests on the material. The use is manual. The pressure, the sealing time and the temperature must be managed by the operator. The sealing result depends exclusively on its ability and therefore the result can vary between seals. The coating of the anti-adhesive Teflon roller allows to seal bags in polypropylene, polyethylene and laminated materials. It is supplied complete with a mat in silicone material which, positioned under the product to be sealed, is the ideal match for sealing.

The Arrow V3 tamper-evident polypropylene tightening seal. The structure of the seal features a catch, a locking mechanism, and a tail part. The locking mechanism is equipped with a collet of unique design made of stainless steel. The operating length of the seal is 385 mm (15.16"). Seal is produced with labels on the back side The locking mechanism features the leaves of the collet that are pointed in one direction, thus blocking the reversal movement of the seal tail, and preventing its opening unnoticed. If anyone tries to open the seal and pull out the tail - the lock cuts the tail off and the seal can not be restored. A transparent cap is placed on top of the collet, which protects it from external damage and makes it possible to check its integrity at any time. The cap also glows under the UV light, which makes it easier to detect the seal or check it in poor light or darkness by using a special UV flashlight.

PGS is a locking device for pipes made of polycarbonate or polypropylene. It is designed to seal cap nuts to prevent their twisting and disconnection of pipes, as well as the removal of gas meters and installation of bridge cables for bypass devices for the purpose of stealing gas. The pipe locking device consists of two semicircular-shaped parts with additional holes for the sealing rope. To install the pipe locking device, it is necessary to connect both parts on the mounting nut, put the sealing rope into the special holes on the sides of PGS, and install the seal (rotary or latch one). The seal should be placed as close as possible to the locking device. The tamper-evident seal and rope will prevent intruders from keeping the fact of removal of the seal and the locking device from the nut unnoticed. When an attempt is made to perform certain actions with the aim to steal gas or water, visible signs appear on the seal, which is evidence

Arrow V2 is a tamper-evident seal produced of polypropylene. It is a tightening seal by the structure that features a catch, as well as a tail part, there is a locking mechanism between them, it is protected by a special cap. The seal catch helps to conveniently fasten the seal and provides a space for identifying information, such as a unique number and other details. The operating length of the seal is 215 mm (8.47”). Clixar products are additionally protected by laser marking with a unique eight-digit identification number on the catch, as well as on the seal's cap. This type of marking is made through the thickness of the seal surface, which prevents the chance to erase the number without a trace, apply a new one, or replace it without any visible evidence. In addition, Clixar offers customers the opportunity to apply their company logo, QR and bar codes, and other relevant information.

Arrow Lux is a tightening seal made of polypropylene. It features a tightener with a catch and a tail part; there is a locking mechanism with a protective cap between them. The catch of the seal is designed for convenient fastening, as well as displaying identifying information: unique number, logo, and other details. The operating length of the seal is 385 mm (15.16") Another degree of protection of Clixar seals is laser marking with a unique eight-digit number on the catch and cap. It is applied through the thickness of the surface of the seal, thus, it is impossible to erase the marking completely and apply a new number or replace the seal. We also provide the opportunity to apply your company logo, QR and bar codes, and other information on the seal catch.

Designed to be used as lockable filler ports for hydraulic reservoirs, allowing the reservoir to breathe whilst protecting it from contamination found in harsh environments Types ▪ SMBL-C (Clamping version) ▪ SMBL-P (Screw-in version) ▪ SMBL-P (Push-on version) Features ▪ Available as clamping version (with 3 clamping jaws), as threaded version (with female BSP thread) or push-on version, suitable for stand pipe mounting with pipe diameters up to 77,5 mm / 3.05 in (secured by 3 locking screws) ▪ Key-lockable cap (2 keys included) ▪ Lock protected by rotating flap ▪ Air flow in both directions, one direction only or no direction Materials ▪ Breather cap made of Aluminium, lacquered (light-grey, RAL 9022) ▪ Breather body made of Aluminium, zinc-plated ▪ Basket made of Steel, zinc-plated or Polypropylene (PP) ▪ Sealings made of NBR (Buna-N®) (standard option); FPM (Viton®) sealed version available Technical Data ▪ Operating temperature range: -30 °C ... +100 °C / -22 °F ......

Manufactured out of thick- walled polypropylene molded blocks Raw Material : PP Reliability and robustness due to SOMEFLU experience of heavy polymer injection Internal construction parts made out of steel and polypropylene Single and robust sealing with anti acid O-rings duplicate molding Max flow : 60 m³ / h Max delivery head : 50 m

Spare parts for conveyor systems Bearing inserts from — galvanized sheet steel (with oiled ball bearing, in antistatic design) — Plastic, grey (polypropylene), with black plastic seal (polyamide) and stainless steel balls — Plastic, black (polypropylene), with black plastic seal Labyrinth (polypropylene) and RS deep groove ball bearing (in antistatic design) — Plastic, blue (polypropylene) with blue (polypropylene) and double stainless steel ball row Pipe diameter: — 20x1.5 mm — 30x1.5 mm — 30x2 mm — 40x1.5 mm — 40x2.3 mm — 50x1.5 mm — 50x2.8 mm — 60x2 mm Axle diameter: — 6 mm — 8mm — 10mm — 12mm

The UniStrap 412 S/L/XL (Short / Long / Extra-Long) security seal is a strong polypropylene pull through security seal with a 40KgF pull apart strength. The UniStrap 412 seal is available with optional tear-off facility for easy-removal by hand, and is available in three different sizes to suit your particular needs, including extra-long 51cm option.

The DoubleLock ring seal is a fixed length polypropylene truck & trailer security seal with polyacetal inner lock for enhanced anti-tampering. The Doublelock seal has a protruding tail once engaged, giving users a visual check that seal has been fully engaged and has not been tampered with. It is commonly used as transport anti-tamper and anti-theft sealing solution for truck and other road freight - particularly for sealing trailer locking hasps or curtain sider buckles.

We offer two product variants: firstly, a Dry Lithium Heparin syringe, wherein the heparin is encapsulated within a small paper substrate contained within the syringe. Secondly, a Pulverized Lithium Heparin syringe, whereby the heparin is finely dispersed and applied to the interior walls of the syringe via a spray mechanism. This innovative design facilitates precise mixing of the blood with heparin and effectively prevents clot formation, representing a testament to modern technological advancements. › Polypropylene › High sealing › 2ml / 2.5ml syringe size With or Without Needle › Easy and comfortable piston movement › Piston stop for safety › Transparent film packaging › EO Sterilization

The Acme X Seal is a versatile smooth ribbon pull-tight seal manufactured from Polypropylene material. The design features rolled heat staking technology to secure the metal spring insert to the body, which provides clear evidence of tampering if forced open or cut. The seal can be manufactured with a Short Tag (ST) or Long Tag (LT) in three different lengths and with a 2mm diameter ribbon making this seal ideal for most applications particularly where there are small sealing apertures. Recommended applications Airline in-flight duty free or Catering Trolleys, Baggage, Refineries, Fuel and Oil Tankers, Chemical Drums, ATM Dispensers, Coin Boxes, Cash Bags, Gaming Machines, Postbags, Fire doors, Lockers Material Body - Polypropylene Insert - Spring Stainless Steel ** Click for more **