Electronics - Import export

Building wires with copper cores, PVC insulation/ polymer halogen free composition, inner PVC/ polymer halogen free composition covering, sheath.Application: building wires are used for the installation of power equipment, mechanisms and machinery, power lines of the domestic uses. PVC -insulated/ halogen free/ fire resistant/ flame retardant/ cold resistant/ low smoke/ low smoke and toxic fumes/ shielded

Copper busbars are produced of electrical copper. The products are convenient in use, practical and durable. Copper busbars have high bandwidth and don't require additional service. The life cycle of the copper busbar is longer than the cable's one. The installation of the copper busbar is easier.

Scanning Thermal Microscopy (SThM) is an advanced SPM mode intended for simultaneous obtaining nanoscale thermal and topography images. NTMDT’s SThM kit is able to visualize temperature and thermal conductivity distribution at the sample surface. The SThM system hardware includes electronic controller, software, and probes. SThM mode of operation with an AFM requires a specialized probe with a resistor built into the cantilever. NTMDT’s SThM module allows one to monitor the resistance changes correlated with the temperature at the end of the probe. So the system is able to monitor relative changes of sample temperature and thermal conductivity. NTMDT’s thermal probes provide better than 100 nm lateral resolution for both topography and thermal images. The specialized SThM cantilever, made of SiO2 with a thin metal layer, is deposited on the probe in such a way that the highest resistance portion of the layer is concentrated near the tip apex.

The RC74201 dry contact card (art. CNRL004) is designed to monitor and control the UPS using potentialfree relay contacts. Monitoring is carried out through the relay contacts built into the card, which switch when the corresponding events occur in the UPS. The dry contact card allows you to remotely monitor the status of the UPS by receiving discrete signals when the relay is activated. The relay contacts are not galvanically connected to the electrical circuits of the UPS. An external power supply must be used to obtain the required signals. It also provides the ability to remotely shutdown the UPS by sending a signal to the corresponding port. The use of relay contacts allows the UPS to be integrated into local dispatch systems at customer sites.

SNMPcard DA807 (art. CNDA807) is designed to monitor the status and control of the UPS via a local area network or the Internet. Monitoring, control and configuration are carried out through the builtin WEBinterface, TelNet or NMS, with the provision of automatic correct shutdown of servers and workstations connected to the UPS. The SNMP card allows you to remotely monitor the values ​​of the input and output parameters of the UPS, the battery charge level, notify the user about system events and alarms through the builtin WEB interface, via the SNMP protocol (including by sending Trap messages in the event of emergency situations) and by sending messages by email. It also provides the ability to remotely control the UPS (reboot, activation of tests, on / off sound notification). This card model supports encryption protocols. The builtin USB port allows you to connect external optional peripherals.

SNMP card DL802 (art. CNDL802) is designed to monitor and control the UPS over a local area network or the Internet. Monitoring, control and configuration are carried out through the builtin WEBinterface, TelNet or NMS, with the provision of automatic correct shutdown of servers and workstations connected to the UPS. The SNMP card allows you to remotely monitor the values ​​of the input and output parameters of the UPS, the battery charge level, notify the user about system events and alarms through the builtin WEB interface, via the SNMP protocol (including by sending Trap messages in the event of emergency situations) and by sending messages by email. It also provides the ability to remotely control the UPS (reboot, activation of tests, on / off sound notification)

External SNMPcard DY522 (art. CNDY522) is designed for monitoring and controlling the UPS via a local area network or the Internet. Monitoring, control and configuration are carried out through the builtin WEBinterface, TelNet or NMS, with the provision of automatic correct shutdown of servers and workstations connected to the UPS. The SNMP card allows you to remotely monitor the values ​​of the input and output parameters of the UPS, the battery charge level, notify the user about system events and alarms through the builtin WEB interface, via the SNMP protocol (including by sending Trap messages in the event of emergency situations) and by sending messages by email. It also provides the ability to remotely control the UPS (reboot, activation of tests, on / off sound notification). This card model supports encryption protocols. An external power supply is supplied with the card.

External SNMPcard BY506 (art. CNBY506) is designed to monitor the status and control of the UPS via a local area network or the Internet. Monitoring, control and configuration are carried out through the builtin WEBinterface, TelNet or NMS, with the provision of automatic correct shutdown of servers and workstations connected to the UPS. The SNMP card allows you to remotely monitor the values ​​of the input and output parameters of the UPS, the battery charge level, notify the user about system events and alarms through the builtin WEB interface, via the SNMP protocol (including by sending Trap messages in the event of emergency situations) and by sending messages by email. It also provides the ability to remotely control the UPS (reboot, activation of tests, on / off sound notification). This card model supports encryption protocols. Builtin additional ports allow you to connect external optional peripherals. An external power supply is supplied with the card.

SNMPcard CY504 (part no. CNCY504) is designed for monitoring and controlling the UPS via a local area network or the Internet. Monitoring, control and configuration are carried out through the builtin WEBinterface, TelNet or NMS, with the provision of automatic correct shutdown of servers and workstations connected to the UPS. The SNMP card allows you to remotely monitor the values ​​of the input and output parameters of the UPS, the battery charge level, notify the user about system events and alarms through the builtin WEB interface, via the SNMP protocol (including by sending Trap messages in the event of emergency situations) and by sending messages by email. It also provides the ability to remotely control the UPS (reboot, activation of tests, on / off sound notification). This card model supports encryption protocols.

SNMPcard DA806 (art. CNDA806) is designed to monitor the status and control of the UPS via a local area network or the Internet. Monitoring, control and configuration are carried out through the builtin WEBinterface, TelNet or NMS, with the provision of automatic correct shutdown of servers and workstations connected to the UPS. The SNMP card allows you to remotely monitor the values ​​of the input and output parameters of the UPS, the battery charge level, notify the user about system events and alarms through the builtin WEB interface, via the SNMP protocol (including by sending Trap messages in the event of emergency situations) and by sending messages by email. It also provides the ability to remotely control the UPS (reboot, activation of tests, on / off sound notification). This card model supports encryption protocols. The builtin MiniUSB port allows you to connect external optional peripherals

SNMP card DY806 (art. CNDY806) is designed to monitor and control the UPS over a local area network or the Internet. Monitoring, control and configuration are carried out through the builtin WEBinterface, TelNet or NMS, with the provision of automatic correct shutdown of servers and workstations connected to the UPS. The SNMP card allows you to remotely monitor the values ​​of the input and output parameters of the UPS, the battery charge level, notify the user about system events and alarms through the builtin WEB interface, via the SNMP protocol (including by sending Trap messages in the event of emergency situations) and by sending messages by email. It also provides the ability to remotely control the UPS (reboot, activation of tests, on / off sound notification). This card model supports encryption protocols. Builtin MiniUSB port allows connection of external optional peripherals

SNMPcard DY801 (art. CNDY801) is designed to monitor the status and control of the UPS via a local area network or the Internet. Monitoring, control and configuration are carried out through the builtin WEBinterface, TelNet or NMS, with the provision of automatic correct shutdown of servers and workstations connected to the UPS. The SNMP card allows you to remotely monitor the values ​​of the input and output parameters of the UPS, the battery charge level, notify the user about system events and alarms through the builtin WEB interface, via the SNMP protocol (including by sending Trap messages in the event of emergency situations) and by sending messages by email. It also provides the ability to remotely control the UPS (reboot, activation of tests, on / off sound notification). This card model supports encryption protocols.

SNMPcard DJ801 (art. CNDJ801) is designed to monitor and control the UPS over a local area network or the Internet. Monitoring, control and configuration are carried out through the builtin WEBinterface, TelNet or NMS, with the provision of automatic correct shutdown of servers and workstations connected to the UPS. The SNMP card allows you to remotely monitor the values ​​of the input and output parameters of the UPS, the battery charge level, notify the user about system events and alarms through the builtin WEB interface, via the SNMP protocol (including by sending Trap messages in the event of emergency situations) and by sending messages by email. It also provides the ability to remotely control the UPS (reboot, activation of tests, on / off sound notification)

SNMPcard BY505 (art. CNBY505) is designed to monitor and control the UPS over a local area network or the Internet. Monitoring, control and configuration are carried out through the builtin WEBinterface, TelNet or NMS, with the provision of automatic correct shutdown of servers and workstations connected to the UPS. The SNMP card allows you to remotely monitor the values ​​of the input and output parameters of the UPS, the battery charge level, notify the user about system events and alarms through the builtin WEB interface, via the SNMP protocol (including by sending Trap messages in the event of emergency situations) and by sending messages by email. It also provides the ability to remotely control the UPS (reboot, activation of tests, on / off sound notification). This card model supports encryption protocols. Builtin additional ports allow you to connect external optional peripherals.

This external bypass module is intended for use with UPS FROSTYLE11, 13 kVA. In Normal Mode, the UPS connects to utility power through the bypass module and provides uninterrupted power to the load. In Bypass Mode, the load is switched to power directly from the external network, bypassing the UPS circuits. The UPS input and output are completely isolated from the loads and the mains. In this mode, the UPS can be safely (and without disconnecting the load) removed from the system for maintenance or replacement

The dry contact board (relay card) is used to provide the UPS peripheral monitoring interface. Contact signals can indicate the current status of the UPS. The appearance and pin numbering of the dry contact relay board may differ depending on the UPS model

Electrical and electronic equipment mounted inside a cabinet generate heat that raises the temperature internal air. Over time, the ever increasing heat can cause sensitive devices to malfunctions. Additionally, heat accumulation can cause circuit breakers to trip which can result in system shut down. Fan filter units are used for enclosure climate control to dissipate heat from within the enclosure to prevent the premature failure of the equipment inside it. It helps to increase an operational reliability and a service life for electrical and electronic systems. Filter fans will cool enclosures to a level slightly above the ambient temperature outside the cabinet. To cool enclosure contents, the fans draw filtered ambient air into the cabinet. At the same time, the heated air within the cabinet is blown out an exhaust. The exhaust is also filtered which creates airflow resistance and a slightly higher pressure inside the enclosure.

Electronic equipment installed inside a cabinet emits heat, which raises the internal temperature. Over time, rising temperature can cause electronic devices to a fail. Thermoelectric Coolers or Thermoelectric Assemblies are designed to divert an excess heat from electronic equipment installed inside an electrical enclosure. NSBox-ICE is a special series of electrical enclosures with installed thermoelectric assembly. The units are mounted in various series of electrical enclosures with protection category IP66 / NEMA4: powder-coated sheet metal, glass reinforced polyester, depending on the field of application and operating conditions. The basic kit includes the selected assembly with a thermostat, a mounting plate with DIN rails for customer equipment, terminal blocks, a circuit breaker, an electrical grounding bar, the set of selected cable glands. The cable glands are mounted in the bottom of the enclosure, e.g. on a removable metal plate for sheet metal cabinet.

Research and development work (R&D) is aimed at creating a new product or technology on the Customer’s specification. We perform: - Complex survey, research and development work in the field of robotics and mechatronics; - Development, design of complex robotic solutions with a guaranteed result: creating an experimental / mock-up / pre-production sample with the parameters specified in the technical specifications with a full package of design and software documentation. Effects of cooperation: 1. Guaranteed completed R&D program; 2. Saving money on R&D up to 40% and reducing the R&D performance period up to 2 times, from doing it on your own; 3. The reputation of the enterprise / department / Customer's department successfully and effectively implementing innovative projects.

The company serially produces high-torque synchronous brushless electric motors of the series AT Drive in a frame and frameless versions with a power from 150 W to 550 W. The design allows it to be installed in products for various purposes. Motors with an axial arrangement of magnets have following advantages: - High torque; - Small diameter; - High rate of peak torque; - Compound of stator winding is resistant to the temperature shock from -60 C till +170 C; - Frameless version; - Hollow rotor; - Tuning agility of motor characteristics within 20%; - Possibility to change winding commutation method. Warranty period: 12 months.

Compact direct current electronic control unit IBP8k-2,0/48R-4.4 is designed to ensure uninterrupted operation of telecommunication equipment with power up to 8 kW. Thanks to the modular design, power units easily replaceable during repair and maintenance. Operating range of AC power supply network is from 85 to 300 V with short-term emissions of up to 350 V. Thermal compensation system for the battery charge voltage allows extending its service life. EPU case made in the standard format of a 19" telecommunication rack with a height of only 2U, which ensures its compact placement. Remote monitoring of operation via RS-232/485 and SNMP is possible.

The company is opened for cooperation in terms of Electronics Manufacturing Services / Licensed Production / Products Localization for the Russian market. The company’s competence covers all production activities enabling the full cycle of product development, from an idea to serial production based on LEAN manufacturing principles. Both small batches and serial products with equally high quality can be produced without minimum order quantity limit. Our capabilities: R&D, industrial design; EEE parts procurement and testing; PCB production; SMT/THT; Mechanical processing; Cables and winding parts production; Hybrids production; Assembly production; Testing of finished products.

The MNP-M7 navigation receiver is designed to determine current coordinates, altitude, speed and time by signals of satellite navigation systems GLONASS, GPS and SBAS (WAAS, EGNOS). The receiver module is a single-sided PCB with contact pads for SMT; it can be easily integrated with navigation systems. The product can be applied in high-precision navigation systems including systems with fast-moving objects, vehicles movement control systems for railway / automobile / air / marine / river, and other types of transport.

NeuroStim is a method that increases the level of health and treatment quality by means of chromotherapy and auditive stimulation. Cannot be used without an interface block. The module can: • boost and improve memory; • raise the intelligence level; •improve physical endurance; •improve mental activity; • increase the creative potential; •activate study skills; •even out the psycho-emotional state; •improve and regulate sleep; •carry out recovery after loads (emotional, physical); • undertake measures against stress; • to improve the psychophysiological condition of an athlete, to rationally prepare for competitions; •assist in conducting breathing sessions, meditations; •help to relax and energize.

The IU-01 Industrial Panel is a human-machine interface based on industrial PC architecture and originally designed as a part of a train safety system for guiding an operator to monitor and control a rolling stock drive including overspeeding control, temperature, motioning, safety and other train systems control. Its dependable performance and robustness allows applying IU-01 in other harsh environments to operate automobile and marine vehicles as well as agricultural and customized machinery and equipment. IU-01 can be associated with a numerous functional systems of vehicles, and its functionality can be programmed as per customer specific requirements.

Carries out spectrophotometric analysis with the registration of arterial temperatures infrared radiation. Cannot be used without an interface block. The module can: • noninvasively obtain 85 biochemical parameters of peripheral and hemodynamic blood composition; • obtain hemodynamic parameters; • obtain various information about the oxygen transportation in the blood; • analyze the cardiovascular system activity; • study affiliation with the hematopoietic, immune and enzyme systems of the body.