Lubricants- synthetic - Import export

Castrol Transmax Manual Transaxle 75W-90 is a modern, fully synthetic high-performance manual transmission lubricant. Advantages excellent wear protection and shiftability for optimal use in transaxle transmissions - extended transmission service life minimized switching forces under all climatic conditions special protection during cold starts due to low pumping capacity reduced temperature level and excellent transmission cleanliness with extended service life Specifications API GL-4+ VW 501 50 SAE Class according to J306 before 1998

High-quality and modern coolants ensure maximum protection against high thermal loads in car and commercial vehicle engines. The use of modern coolants can extend the lifespan of engines and minimize potential damage as well as downtimes. We offer a wide range of coolants from our partners Aral and Castrol. Together we will find the right coolant to meet your specifications and requirements.

In 2015 the product name was changed. The old product name was Castrol Viscotemp 2. Fully synthetic high-temperature lubricating grease Description Castrol Molub-Alloy 100-2 HT (previous product name Castrol Viscotemp 2) is a fully synthetic high-temperature lubricating grease for use at high continuous temperatures. It enables long-term lubrication of plain and rolling bearings and other grease lubrication points at high operating temperatures, high bearing pressures and aggressive environmental conditions. Application Castrol Molub-Alloy 100-2 HT is a high-temperature grease for the lubrication of rolling and plain bearings and is used in fan bearings in hot air flow, calender bearings, baking systems and continuous drying chambers as well as for overhead conveyors of painting lines that are exposed to chemical influences, as well as in cold or influence of hot water and steam. Instructions for use Temperature range: -20 °C to +220 °C

In 2015 the product name was changed. The old product name was Castrol Viscotemp 2. Fully synthetic high-temperature lubricating grease Description Castrol Molub-Alloy 100-2 HT (previous product name Castrol Viscotemp 2) is a fully synthetic high-temperature lubricating grease for use at high continuous temperatures. It enables long-term lubrication of plain and rolling bearings and other grease lubrication points at high operating temperatures, high bearing pressures and aggressive environmental conditions. Application Castrol Molub-Alloy 100-2 HT is a high-temperature grease for the lubrication of rolling and plain bearings and is used in fan bearings in hot air flow, calender bearings, baking systems and continuous drying chambers as well as for overhead conveyors of painting lines that are exposed to chemical influences, as well as in cold or influence of hot water and steam. Instructions for use Temperature range: -20 °C to +220 °C

Castrol Syntrax Longlife 75W-90 is a fully synthetic axle gear lubricant for cars, heavy and light commercial vehicles and tractors. The performance reserves of Castrol Syntrax Longlife 75W-90 exceed the API class GL-5 and allow a significant extension of the existing oil change intervals (according to manufacturer regulations). Castrol Syntrax Longlife 75W-90 can be used in all axle drives and differentials without a multi-plate lock if a GL-5 lubricant with SAE 75W-90 is required. Advantages -Extremely high pressure absorption capacity -Excellent high-temperature stability -Significantly reduced gear oil temperature -Absolute shear stability -Excellent lubrication security at very low temperatures -Neutral sealing behavior -Excellent foam resistance -Extended oil change intervals possible (observe manufacturer's instructions) Specifications API GL-5 MAN 342 Type S1 Scania STO 1:0 ZF TE-ML 05A,12B,17B,19C,21A BMW (Non LS Rear Axles)

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body Stainless steel 1.4408. Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4401 (316) Stem Stainless steel 1.4404 (316) Function Electric acting Pressure discharge One-sided Voltage 400V 3AC (24V DC, 230V AC on request) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Function Electrical operated Pressure discharge bidirectional Stem Not rising Pressure range Please refer to the data sheet Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy-coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Electric acting Pressure discharge One-sided Voltage 400V 3AC (24V DC, 230V AC on request) Pressure range Please refer to the table Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Refer to the advices on page 8! Body Stainless steel 1.4408 Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4401 (316) Stem Stainless steel 1.4404 (316) Function Pneumatic single acting with spring return, normally closed (NC). Pressure discharge One-sided Pilot pressure 6bar Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the table Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 Installation Only with vertical upwards actuator The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Refer to the advices on page 9 and 11! Body GG-25 (grey cast iron), epoxy coated 120 … 180µm (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Function Pneumatic single acting with spring return, normally closed (NC). Pressure discharge bidirectional Pilot pressure 6bar Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the table Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Refer to the advices on page 8! Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Pneumatic single acting with spring return, normally closed (NC). Pressure discharge One-sided Pilot pressure 6bar Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 Installation Only with vertical upwards actuator The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body Stainless steel 1.4408 Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4401 (316) Stem Stainless steel 1.4404 (316) Function Pneumatic double acting Pressure discharge One-sided Pilot pressure 6bar (lower pressure on request) Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Pneumatic double acting Pressure discharge bidirectional Pilot pressure 6bar (lower pressure on request) Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Pneumatic double acting Pressure discharge One-sided Pilot pressure 6bar (lower pressure on request) Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body Stainless steel 1.4408 Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4401 (316) Stem Stainless steel 1.4404 (316) Lever Steel, lacquered Pressure discharge One-sided Stem Not rising Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Lever Steel, lacquered Pressure discharge bidirectional Pressure range Please refer to the table Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Lever Steel, lacquered Pressure discharge One-sided Stem Not rising Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Hand wheel Steel, lacquered Pressure discharge bidirectional Stem Not rising Pressure range Please refer to the data sheet Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Hand wheel Steel, lacquered Pressure discharge One-sided, two-sided on request Stem Not rising Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid