Concrete slab - Import export

Support for concrete slabs made by recycled antischock (HIPS) material. Using area: door and window support of construction. 120*80*3 mm to 120*80*16 mm

TECHNICAL PROPERTIES Primer filler for vertical surfaces or for use on ceilings made from poured concrete or pre-slabs. Decorating filler, for smoothing over. Smooth, matt finish. Odour-free. COMPOSITION AND APPEARANCE. Solvents : Water. Filler : Calcium carbonates. Additives : Dispersing agent, bactericidal fungicide. Thickeners : Cellulosic, polyacrylates. Binders : Acrylic dispersing agent. Density : 1.86. Dry matter : 75%. TECHNICAL PROPERTIES • Fire classification: A2-S1, d0 SUITABLE SURFACES Interior : ideal for covering bricks, brick tiles, cement breeze blocks, cinder blocks, de-bubbling pre-slabs, shuttered concrete, aerated concrete, for redecorating stippled walls or old damaged surfaces. APPLICATION. • The first coat should be levelled out using 60 cm scraper or skimmed with a rule. • After drying, the second coat should be smoothed with a scraper. • After allowing to set slightly, squeeze the filler at a slight angle using a clean scraper.

TECHNICAL DEFINITION Levelling filler for vertical substrates and for use on ceilings for poured concrete or pre-cast slabs. Ideal for the preparation of pre-cast slabs, formwork concrete and for the renovation of textured finishes or fibreglass with a paint finish. TECHNICAL CHARACTERISTICS • Dry extract : 75% • Density : 1.86 • VOC content : less than 1g/l COMPOSITION AND APPEARANCE Water, calcium carbonate, dispersant, bactericide, fungicide, cellulosic fibres, polyacrylates, clays, acrylic dispersant. AMOUNT REQUIRED From 2 to 4 kg for the first coat. From 1.5 to 2 kg for the second coat. APPLICATION SEMIN AIRLESS EXTREM filler is sprayed using the Airless pump or rotor machine/Flat spray stator in 2 coats. The first coat must be levelled using a 60 cm blade or levelled with a straight edge. After drying, the second coat must be smoothed using a blade.

TECHNICAL DEFINITION SEMIN AIRLESS is an interior finishing coating designed for Airless projection. It is ideally suited to the preparation of pre-slabs, walled concrete and plasterboards before painting. COMPOSITION AND APPEARANCE Emulsion acrylic resin, mineral filler, cellulose derivatives, conservation agent and various additives. ACCEPTED SUBSTRATES • Pasterboard • Filling coatings • Old paintwork • Smoothed concrete • Plaster blocks SUITABLE SURFACES SEMIN AIRLESS can be covered with any acrylic or oil-based paint. TECHNICAL CHARACTERISTICS • Dry matter: 72% • Density: 1.6 PREPARATION OF SURFACES BEFORE APPLICATION The substrate must comply with DTU 59.1, i.e. be clean, dry, free of dust and of any trace of stripping oil. Plasterboard must be primed. APPLICATION SEMIN AIRLESS can be projected with any type of Airless type 695, 795 or Mark 5 machine, fitted with an Airless tremie and a size 21, 23 or 41 nozzle.

Load capacity: 125 kN test load (EN 124) when filled with a min. 5 cm layer of grade C35/45 concrete (EN 206). Material: Frame and cover in 2 mm cold-formed precision steel profiles. Hot-dip galvanised. High-load hinges. High-specification double-piston gas struts. Features: Comfort-lift access cover. Cover with 10 cm deep recess. With peripheral EPDM seal, smell proof and largely water-tight (not guaranteed to be completely water-tight). Opening tools included. Opening is assisted by the patented double-piston gas struts to such an extent that the cover can be opened and closed by one person. Safety device fitted to prevent the open cover from closing. Applications: For installations which require access without particular effort. Especially for those installations where the cover is to be filled with concrete slabs, bricks, paving stones or paviors etc. Installation: Please study the enclosed installation instructions carefully before installation and pay attention to our...

Load capacity: 250 kN or 400 kN test load (EN 124) when filled with a min. 5 cm concrete. Material: Frame and cover made of steel plate, hot-dip galvanised. Features: Heavy-duty sealed cover with 10 cm deep recess. Underside of cover reinforced with steel girders. In Type BVHS 400, the frame is reinforced with an additional frame. EPDM seal. Robust steel mesh reinforcement. The Lift-Off opening system: Every HAGODECK Type BVHS cover comes with a set of lifting keys and precise installation instructions. The HAGO advantage: jammed covers are released by simply turning the Golden Key. Applications: For use in vehicle traffic areas in industrial buildings and areas surrounding buildings or for secondary traffic areas (pedestrian zones). Especially for those installations where the cover is to be filled with concrete slabs, bricks, paviors etc. Installation: Installation must be carried out according to our instructions. With water-tight models, care must be taken to seal the...

Load capacity: 125 kN test load (EN 124) when filled with a min. 5 cm layer of grade C 35/45 concrete (EN 206) Material: Frame and cover in 2 mm cold-formed precision steel profiles. Hot-dip galvanised. Features: Sealed cover with 10 cm deep recess. Virtually invisible when installed. EPDM seal. Robust steel mesh reinforcement, crosswise welded. Opening tool included. The Lift-Off opening system: Every HAGODECK Type BVH-maxi steel cover comes with a set of lifting keys and clear installation instructions. The HAGO advantage: jammed covers are released by simply turning the Golden Key. Applications: Inside buildings and their surroundings. Especially for those installations where the cover is to be filled with concrete slabs, bricks, paviors etc. Installation: Installation must be carried out according to our instructions. With water-tight models, care must be taken to seal the outer frame into the surrounding flooring. Cover depth ≈ 10.2 cm Installation height ≈ 12.5...

Premium oil-, water-, dirt- and stainproof impregnating sealer for high quality concrete products, frequently used for surface-treated (shotblast, ground, bush-hammered) concrete paving blocks and slabs. Water-based, strong water beading and oil beading effect, superior easyto- clean effect.

High increase of compaction and strength in the production of concrete products, esp. pavers, slabs, curbs, lawn edgings; optimization of cement content. Synthetic high-performance plasticizer for highest strength development at optimized cement content.

It’s a highly effectiv pasticizer which provides top strength with a low cement content, especially in earth-moist concrete. PAVELITH® KB 600 hast been especially developed for the production of all concrete block products made of earth-moist concrete, such as concrete paving stones, curbstones, paving slabs, non-standard concrete components, such as grass pavers, curbstones, garden slabs, angle stones, etc. - improved filling action - dense concrete structure - improved cement hydratio - high strength at low cement content - dense, visually appealing surfaces - good side sealing

The cost of construction is much lower than a traditional concrete construction. Assembly is quick. You can erect your prefabricated studiostyle home in a few hours. Maintenance costs are low. The civil engineering costs for the construction are low. It is installed on lightweight concrete (concrete slab or plinth). The prefabricated home structure has an average lifespan of 60 years. The design is performed according to the architectural requirements requested. Our interior architects can assist you with the many options we can offer for your home (custom kitchen, various bathroom options, etc.) Fully insulated house that meets your thermal and sound insulation requirements. Prefabricated construction complying with antiseismic standards. Tailored construction complying with anticyclonic standards, particularly those applicable in the Caribbean countries. Technical assistance with the help of a supervisor or an assembly team to see to the installation of your project.

INOX® Path Clean is a highly concentrated fast-acting biological cleaning agent for the sustainable cleaning and maintenance of your stone slabs, concrete surfaces, paths as well as gravel passages & pebbles. According to the Plant Protection Agency, it is not to be used as a weed killer. Therefore, do not spray on plants, as they will die after a short time.

Can be successfully used for the production of all concrete block products made of earth-moist concrete, such as paving stones, slabs, curbstones, garden stones, bricks made of pumice, LAVA, LECA or similar. - higher water absorption - significantly better workability and greater compactibility - improved filling prperties - increased strength - higher freeze-thaw resistance -cement savings of up to 10-15% or higher share of pozzolanic additives possible - significantly improved appearance thanks to the closed concrete structure

Especially ideal for laying concrete pavers on patios and balconies. Concrete and natural stone slabs can be laid quickly and precisely. Our pedestal support with four separately adjustable support points, various positioning lugs, and integrated locking mechanism can be increased to at least 260mm overall height by combining with various VOLFI System components. Pro Tip: VOLFI 4-C Pedestals are probably the only supports making it easy to use slabs of different types on the same raised flooring.

Concrete additive for high water retention of the mixture in order to achieve high density of face and core concrete of paving stones, slabs and kerbstones; proven in large-format paving slabs. Allows adjustment of an optimal water content, reduction of sticking at the machine stamp, improves structural density significantly, increases early and final strength, improves resistance to freeze-thaw with de-icing salt and abrasion resistance.

It has been especially developed for the production of colored concrete block productsmade of earth-moist concrete and combines multiple mechanisms. PAVELITH® AP 600 can be successfully used in concrete block products made of earth-moist concrete, such as paving stones, slabs or gardening products, as well as in mixtures of plastic consistency , such as wet-cast products. - intensified color effect - improved color stability - enhanced color brilliance - minimized primary and secondary efflorescence - reduced atmospheric water absorption - very good side and surface sealing - greatly reduced tendency for sticking

It has been especially developed for the production of colored concrete block productsmade of earth-moist concrete and combines multiple mechanisms. PAVELITH® AP 600 can be successfully used in concrete block products made of earth-moist concrete, such as paving stones, slabs or gardening products, as well as in mixtures of plastic consistency , such as wet-cast products. - intensified color effect - improved color stability - enhanced color brilliance - minimized primary and secondary efflorescence - reduced atmospheric water absorption - very good side and surface sealing - greatly reduced tendency for sticking

Has been especially developed for the production of colored concrete block products from earth-moist concrete. Can be successfully used für the production of all concrete block products made fo earth-moist concrete, such as paving stones, slabs, embankment stones, palisades, etc. - minimized primary and secondary efflorescence - intensified color effect - good side and surface sealing - reduced tendency for sticking - increased strength - reduced water absorption thanks to a denser concrete structureand - - waterproofing effect

Has been especially developed for the production of colored concrete block products from earth-moist concrete and combines multiple mechanisms. Can be successfully used for the production of all concrete block products made of earth-moist concrete, such as paving stones, slabs, embankment stones, palisades, etc. -minimization of primary and secondary efflorescence -intensifies the color effect and improves color stability -features a strong plasticization effect -higher density of concrete blocks -good side and surface sealing -reduced tendency for sticking

Can be successfully used for the production of all concrete block products made of earth-moist concrete, such as paving stones, slabs, embankment stones, palisades, etc. -enhanced color brillance - reduced tendency towards lime efflorescence and ferrous efflorescence/ discoloration - very good anti-adhesive effect - allows for the creation fo an optimal moisture content in concrete face mixes - improved filling properties - reduced shrinkage cracks in face mix concrete - very good surface and side sealing

Bitumer Flexigum PU is a one-component bitumen-polyurethane compound that forms a permanently flexible and chemically resistant fastening and stress transfer compound. Bitumer Flexigum PU finds its use in: •for continuous resilient fixing of the rail as a subfloor, •rail fastening compound and as a lagging for the underfloor, •for making permanent and flexible expansion joints between concrete slabs and elements made of steel, •filling the gaps located between the road strip and the rail, •for filling concrete-to-concrete joints •filling joints, gaps, cracks and expansion joints in heavily worked asphalt and concrete pavements ( e.g., curbs on bridges), •filling joints "working" on steel and concrete bridges and other pavements characterized by strong movements.

hydraulic demolition hammer for Ferrum DM yard loader / wheel loader suitable for all models listed below requires 3rd control circuit with connection for quick coupler Ideal for breaking up masonry, concrete slabs and asphalt => We can also do any other for a small additional charge Deliver the recording appropriately . All we need are the exact dimensions and a drawing. Please contact us if necessary. Recommended for: Wheel loader Ferrum DM308 x4 V2 Ferrum DM312 x4 Ferrum DM416 x4 V2 Ferrum DM522 x4 Ferrum DM430 x4 DLZ Ferrum DM625 x4 Ferrum DM732 x4 Court loader: Courtyard loader FIRST 12 Courtyard loader FIRST 16

Reliable lateral protection according to safety standard EN 13374 - For a variety of applications (wall formwork, slab formwork, window and door openings, concrete slabs and exposed slab edges and upper wall edges) - Quick, easy assembly - According to safety standard EN 13374 - Use with a protection fence or wooden planks is possible A key element is the railing post lateral protection, which can be used for a range of applications when combined with various connecting parts. Thanks to the flexible application of the lateral protection system, you will save on investment and storage costs.

This cross-shaped anchor for flat roofs is weighed down using concrete slabs (50 x 50 x 5cm, not included). The design is based on a high-quality stainless steel frame (150 x 150 cm) with aluminium crossbars and a central, stainless steel anchorage point for one individual (Ø 16 mm). EN 795:2012, E For flat roof pitches ≤ 5° Weighed down using 8 concrete slabs (ca. 224 kg) Weight incl. ballast: ca. 245 kg; resulting roof load approx. 108.9 kg per m² Also designed for usage as an intermediate post in a lifeline system Incl. 5 EPDM patches to protect your roof membrane

Whether this device is left standing out in the open or integrated into your roof greenery, our ABS Weight OnTop Max anchorage device for flat roof surfaces has been approved for installation without penetrating your roof surface - simply by weighting it down (50 x 50 x 5 cm, concrete slabs not included). Please observe the installation instructions provided in the "abZ" (national technical approval: Z-14.9-824) For flat roof pitches ≤ 5° Weighted down using 40 concrete slabs (ca. 1.120 kg) | resulting roof load approx. 61 kg per m² If implemented as an end or corner post in a lifeline system, a special supporting tube needs to be used

This anchorage device was specially-designed for flat roofs. It can be used as an anchor or system support and can be weighed down using concrete slabs (50 x 50 x 5 cm, not included) or gravel (not included). Its high-quality, stainless steel frame (150 x 150 cm) with aluminium crossbars is equipped with a central anchorage point (Ø 16 mm) - also made of stainless steel. EN 795:2012, E + CEN/TS 16415:2013 For flat roof pitches ≤ 5° Weighed down using 16 concrete slabs (ca. 448 kg) Weight incl. ballast: 483 kg | resulting roof load: approx. 214.7 kg per m² Anchorage point for 2 individuals Weighed down using gravel (ca. 450 kg) Weight incl. ballast: ca. 485 kg | resulting roof load: approx. 200 kg per m² Anchorage point for 1 individual (secures 2 individuals when used as an intermediate bracket in a lifeline system) Additional supporting tube required for usage as an end or corner post Incl. 5 EPDM patches to protect your roof membrane

Thanks to its base plate (150 x 150 mm) and welded-on supporting tube (Ø 42 mm), this stainless steel anchorage point offers plenty of stability when used in a lifeline system installed in a concrete hollow core slab ceiling. Simply install the anchor on the substructure using the 4 slab expansion anchors supplied. National technical approval ("abZ"): Z-14.9-688 (pls. observe the installation instructions provided in the "abZ") EN 795:2012, C & CEN/TS 16415:2017 Base plate + welded-on supporting tube Designed for concrete hollow core slab ceilings ≥ C45/55 (B55) Web depth min. 25mm Installed using 4 expansion dowels Can be installed in cavities and solid material

This stainless steel anchorage point (Ø 16 mm) and matching base plate (220 x 220 mm) - certified by the German Institute for Construction Technology (DIBt) - can be easily installed on a suspended flat roof ceiling made of concrete. The 4 hollow slab expension dowels that come with the device ensure a reliable hold. National technical approval ("abZ"): Z-14.9-688 (pls. observe the installation instructions provided in the "abZ") EN 795:2012, A + CEN/TS 16415:2017 For concrete hollow core slab ceilings ≥ C45/55 Web thickness: min. 25mm Installed using 4x V4A expansion dowels (included) Upgrade with a supporting tube for usage as an end or corner post in a lifeline system

For all sunshade models For permanent installation, each sunshade can also be delivered with an encasable base (2-part). The size of the foundation depends on the sunshade model. The advantage: it saves space and you can remove the upper part by undoing only four screws. Then everything is open and there are no tripping hazards. The models ParaQueen, PyraMax and ParaKing also require a hinged joint.This is an enormous help in putting up and taking down the sunshade in a controlled manner. A level position is still guaranteed when removing the hinged joint. Panel Base For all sunshade models The sunshades can be put up anywhere with this mobile bevelled base. Concrete slabs in the recesses of the base ensure sturdy support. The base is bevelled to avoid hazardous edges for staff and customers. The panel base has the following dimensions: 970 x 970 x 50 mm. With our special King-base you are on the safe side. Our specially treated heavy base is made of 3 mm heat-treated galvanized ste