Cables - accessories - Import export

It is a glass fibre tape covered with a thick layer of red silicone rubber which provides the tape with a high level of heat insulation. It is a very flexible tape, which is suitable for protecting hoses and electric cables by means of bandaging without having to disassemble or disconnect the parts to be covered. It offers continuous protection at operating temperatures of 250°C and can withstand splashes of molten metal up to 1200°C. It is resistant to most oils and fuels, hydraulic fluids, acids and alkalis. Applications Protection of cables, wires and hoses against extreme heat, fire protection, insulation of hoses against loss of heat for the steel and naval industries, industrial furna-ces, automotive sector, foundries, steel works, oil rigs.

In the wire and cable industry, wear plates are an important component in the production process. To increase the lifespans of the plates, we subject them to thermal treatment. The “slip-in” design further minimizes the repair costs. Wear plates available from Heinze & Streng with conventional or “slip-in” design.

PMA cable protection systems are used wherever the mechanical protection of electrical lines and cables is needed. Highly flexible cable protection tubes are specifically suited for the additional protection of cable guides in e-chain® systems. Due to the combination of technical knowhow and the strictest international safety guidelines, PMA fulfils the worldwide requirements of industrial markets in application areas like mechanical engineering, automotive construction, fiber optics, solar systems as well as applications in the robot sector with high speeds and millions of alternate bending cycles.

Other information E3.10 Inner height hi: 10 mm Inner widths Bi: 20 - 60 mm bending radii R: 15 - 48 mm Pitch: 16,7 mm E-Chain®. E3.15 Inner height hi: 15 mm Inner widths Bi: 20 - 60 mm bending radii R: 32 - 75 mm Pitch: 16,7 mm E-Chain®. E3.22 Inner height hi: 22 mm Inner widths Bi: 20 - 60 mm bending radii R: 44 - 75 mm Pitch: 16,7 mm E-Chain®. iF -Design Award 2005 IPA classification - Report IG0704-400:: ISO Class 1, according to DIN EN ISO 14644-1 for system E3, Series E3.15.040.075.0 at v = 0,5 m/s, 1 m/s, 2 m/s Other information E3.10 Inner height hi: 10 mm Inner widths Bi: 20 - 60 mm bending radii R: 15 - 48 mm Pitch: 16,7 mm E-Chain®. E3.15 Inner height hi: 15 mm Inner widths Bi: 20 - 60 mm bending radii R: 32 - 75 mm Pitch: 16,7 mm E-Chain®. E3.22 Inner height hi: 22 mm Inner widths Bi: 20 - 60 mm bending radii R: 44 - 75 mm Pitch: 16,7 mm E-Chain®. E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Selection aids Installation instructions Opening and closing of the E-Chain®. Interior separation and strain reliefs. Assembly Instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. E3 system E3: System for highly dynamic applications The cycle times are always shorter in the automation, whereas the requirements in noise reduction, service life, vibration dampening are always higher. For this wide area of small E-Chain®, igus® now introduces the E3 system product range that completely caters to these requirements: Extremely low noise operation (max. 38 dB(A)). The resilient element replaces pins and bores as fastener Modular chain made of three elements Cost-efficient crossbar and separator "on the band" Quicker and easier access to cables by the zipper system Good stability through stable, interlocked links Easy to shorten or lengthen Ideal for flat cables Accessories: Separators, integrated strain reliefs, mounting brackets Typical industrial sectors and applications Production and processing of semiconductors Optics Automatic insertion machines Materials handling technology Measuring technology Printer and plotter Clean room application General mechanical engineering iF -Design Award 2005 IPA classification - Report IG0704-400:: ISO Class 1, according to DIN EN ISO 14644-1 for system E3, Series E3.15.040.075.0 at v = 0,5 m/s, 1 m/s, 2 m/s

drylin® Q Square linear guides Square section tube made of hard-anodized aluminum Torque resistant without 2nd guidance Tolerates moments up to 10 Nm drylin® Q square section tube drylin® Q - bearing housing, adjustable Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually drylin® Q - bearing housing drylin® Q - bearing housing, adjustable with hand clamp Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually With manual clamp drylin® Q - bearing housing with manual clamp drylin® Q - housing bearing Q20 enclosed, anodized aluminium housing short design or tandem housing Torque resistant without 2nd guidance drylin® housing bearing Q20 drylin® W - flange bearing Flange pillow block made of anodized aluminum Round flange (01 version), square flange (02 version Standard type or tandem housing Torque resistant without 2nd guidance drylin® W - flange bearing drylin® Q - housing bearing Q10 Solid polymer bearing made of iglidur® J Very light Tolerates moments up to 3 Nm Space saving drylin® Q - housing bearing Q10 drylin® Q - accessory Based on a torque resistant square guide with 7.5 mm edge lengths Hollow chamber for supply lines (media, compressed air,cable) drylin® Q - accessory drylin® Q - gripper axis Toothed, hard-coated and corrosion protected square-hollow profile Move loads up to 500 g at speeds of up to 0.7 m/s Bearing made of iglidur® J Drive: NEMA11 stepper motor with gear wheel drylin® Q - gripper axis Move linear torque resistant, completely lubrication-free. The drylin® Q linear construction kit offers the user maximum flexibility in the design Individual housing options such as solid plastic bearings and adjustable complete housings with and without manual clamp are available. Due to the hollow chamber design, the rugged hard-anodised aluminium profile is very light and is suitable for the simultaneous conducting of supply cables. The mounting options are highly variable, among others, using slot nuts; installation size 20 can also combined with all 20/20 aluminium construction profiles. 1. Profile made of hard-anodized aluminum 2. Main body of the carriage made of aluminum 3. Customized clearance adjustment 4. Cover made of solid plastic 5. Gliding elements in high-performance polymer iglidur® J serve as a guide bearing and guarantee optimum running properties drylin® Q Square linear guides Square section tube made of hard-anodized aluminum Torque resistant without 2nd guidance Tolerates moments up to 10 Nm drylin® Q square section tube drylin® Q - bearing housing, adjustable Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually drylin® Q - bearing housing drylin® Q - bearing housing, adjustable with hand clamp Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually With manual clamp drylin® Q - bearing housing with manual clamp drylin® Q - housing bearing Q20 enclosed, anodized aluminium housing short design or tandem housing Torque resistant without 2nd guidance drylin® housing bearing Q20 drylin® W - flange bearing Flange pillow block made of anodized aluminum Round flange (01 version), square flange (02 version Standard type or tandem housing Torque resistant without 2nd guidance drylin® W - flange bearing drylin® Q - housing bearing Q10 Solid polymer bearing made of iglidur® J Very light Tolerates moments up to 3 Nm Space saving drylin® Q - housing bearing Q10 drylin® Q - accessory Based on a torque resistant square guide with 7.5 mm edge lengths Hollow chamber for supply lines (media, compressed air,cable) drylin® Q - accessory drylin® Q - gripper axis Toothed, hard-coated and corrosion protected square-hollow profile Move loads up to 500 g at speeds of up to 0.7 m/s Bearing made of iglidur® J Drive: NEMA11 stepper motor with gear wheel drylin® Q - gripper axis