Shaping - Import export

Shaping dies adopt a central role in many areas of the manufacturing and processing industries. They are of particular significance in the sheet-processing industry. We produce these parts in accordance with your requirements – also in small series. Contact I have read and agree to the privacy policy. *Pflichtfelder

KIRSCH Kunststofftechnik specialises in (re)shaping transparent plastics with high optical quality. In our 4 different forming-furnaces we can process panels and components up to 3000 x 2000 mm of size. Special filtration technology, cleanness and experience contribute to form the transparent panels without dust inclusions. Our furnaces are equipped with modern controls to target individually required heating and cooling curves for each plastic. Thus, we can achieve not only an exact temperature during forming, but also control the cooling process accordingly to accomplish a nearly distortionless plastic. We can process plastics two-dimensional, as well as three-dimensional.

Wires with a particular shape (neither round nor flat wire). Subject to our customers’ specification there are various conceivable solutions such as triangle, polygon, bones or trapeze shape, and many more. Made from Cu-ETP1 and Cu-OF1 in bare, soft annealed or hard. LEONI Histral® alloys upon request. Cross-section: up to approx. 2.5 mm², depending on shape, further cross-sections upon request. Profile wires are mainly suitable for electrical conductors in a plastic profile and for busbars. They are space saving and have bigger contact areas. Certain shapes give a more secure hold in plastic profiles.

Raised access floor socket 8502E with two slots. The housing of the hollow floor tank is made of sendzimir galvanized sheet steel, the frame and the lid are made of polished stainless steel. The lid has two cable outlets and closes in a straight or angled shape even when a standard plug is plugged in. Other equipment variants on request.

• For short, straight and figure cuts, small radii • Cutting edge hardness 57-59 HRC • Cutting edges inductively hardened • Re-adjustable screw-joint • Handles coated with plastic • Made of tool steel, forged, oil-hardened

Various shapes Our model groups 300, 500, 600 and 900

•  operating temperatures up to 600°C (standard) •  completely made of stainless steel •  heat recovery factor up to 85% •  pressure-resistant up to 150 mbar •  completely welded •  high degree of efficiency •  without seelings  •  up to 100% gas-tight •  low maintenance •  small construction volume •  flexible coordination due      to single-item or small-lot production •  distance between plates from 3.5 mm to 7 mm •  available in the structural shapes K, L, U and LU  •  complete seperation of the two gas flows •  different current lines possible •  different volume flows for exhaust and feed air,       applicable for the temperature control of useful heat Structural shape In principle, the shape is arbitrary.  The choice takes place after consulting with the customer and with similar power are no costs involved. It depends on the technical demands of the application.  The structural shape X (crossflow) isn't possible with the ´ THERMO GAS System.     Shape LU  This structural s

•  operating temperatures up to 600°C (standard) •  completely made of stainless steel •  heat recovery factor up to 85% •  pressure-resistant up to 150 mbar •  completely welded •  high degree of efficiency •  without seelings  •  up to 100% gas-tight •  low maintenance •  small construction volume •  flexible coordination due      to single-item or small-lot production •  distance between plates from 3.5 mm to 7 mm •  available in the structural shapes K, L, U and LU  •  complete seperation of the two gas flows •  different current lines possible •  different volume flows for exhaust and feed air,       applicable for the temperature control of useful heat no costs involved Shape U    This structural shape is especially qualified for small plate heat exchangers. This structural shape is although qualified for plate heat exchangers which should streamed vertically.

•  operating temperatures up to 600°C (standard) •  completely made of stainless steel •  heat recovery factor up to 85% •  pressure-resistant up to 150 mbar •  completely welded •  high degree of efficiency •  without seelings  •  up to 100% gas-tight •  low maintenance •  small construction volume •  flexible coordination due      to single-item or small-lot production •  distance between plates from 3.5 mm to 7 mm •  available in the structural shapes K, L, U and LU  •  complete seperation of the two gas flows •  different current lines possible •  different volume flows for exhaust and feed air,       applicable for the temperature control of useful heat Structural shape In principle, the shape is arbitrary.  The choice takes place after consulting with the customer and with similar power are no costs involved. It depends on the technical demands of the application.  The structural shape X (crossflow) isn't possible with the ´ THERMO GAS System.  Shape L    This plate heat exc

•  operating temperatures up to 600°C (standard) •  completely made of stainless steel •  heat recovery factor up to 85% •  pressure-resistant up to 150 mbar •  completely welded •  high degree of efficiency •  without seelings  •  up to 100% gas-tight •  low maintenance •  small construction volume •  flexible coordination due      to single-item or small-lot production •  distance between plates from 3.5 mm to 7 mm •  available in the structural shapes K, L, U and LU  •  complete seperation of the two gas flows •  different current lines possible •  different volume flows for exhaust and feed air,       applicable for the temperature control of useful heat Structural shape In principle, the shape is arbitrary.  The choice takes place after consulting with the customer and with similar power are no costs involved. It depends on the technical demands of the application.  The structural shape X (crossflow) isn't possible with the ´ THERMO GAS System.  Shape K    An absolute classic

More ductile than most lock-welt materials, shaping of this aluminum standing-seam roofing can be done easily to match any architectural application. A wide range of colors and finishes are also available, so designers can be as creative as they wish, knowing what’s on paper can become reality.

We can work with almost any concrete formulation you request. In addition to the formulations based on the DIN/EN standard, we produce customized formulations for you. Our own mold construction department helps us to be flexible in producing sizes and formats according to your specifications. Upon your request, concrete test specimens can be subjected to customized aftertreatment by grinding, saw-cutting or sandblasting.

steel, thickness 10 mm*powdercoated*M 10 threaded*rubber feet

Polyetherimide is an amorphous thermoplastic and part of the polyimide family. It has excellent dimensional accuracy over a wide temperature range and has low thermal expansion. BIEGLO's sales portfolio for PEI contains rods from 8mm to 100mm. The most common applications of PEI are in the food and beverage industry, pharmaceutical and electronics industry as well as precision engineering.

Raised access floor socket 8504B with 4 slots. The housing is made of sendzimir galvanized sheet steel. The Frame and lid made of stainless steel. The lid also closes when standard plugs are inserted in a straight or angled shape. The removable lid can be covered with 15 mm flooring like parquet, cork, carpet, etc. Other equipment variants on request

With the new generation of our combination machines, we have continued to develop the new diversity for forming pipes. Geometries that effectively replace high-cost and expensive turned parts can be formed directly at the pipe end in the endforming machine – for a final component of a single workpiece that is ready for use without elaborate soldering or welding. Implementation of the combination can be specified by you or based directly on the forming geometry. This is usually done using up to 6 axial forming stages and at least one rotary unit. Trimming, as well as axial and rotary forming, may require 2 rotary forming stations. Simple trimming or deburring after forming at the pipe end are no demanding challenges. Therefore, all our axial forming machines and combination machines are equipped with one or several single-drive axes. They have a servo-electrical drive and can be used in each of the holders for the forming stages, making the system is very flexible and compact.

BIEGLO is the official distributor of Saint Gobain Performance Plastics for the Meldin 7000, Polyimide rod. In line with different requirements of the Industrial market, the Meldin product family can provide high temperature resistance, wide chemical resistance, good mechanical properties also at elevated temperatures and low wear, long lifetime. Polyimide rod can be used in temperatures up to 350°C continuously and it has various applications in the automotive, aerospace and electronic industries. Polyimide rods have a standard length of 965mm. The diameters of the solid bars are distributed from 6.3mm to 82.5mm.

PEEK is the ideal replacement for metal and other plastics due to its high temperature resistance of up to 240°C , excellent chemical and wear resistance. The Dexnyl PEEK rods of BIEGLO offer resistance to elevated temperatures, radiation and chemicals. Their dimensional stability and mechanical strength are second to none. Our PEEK has an excellent hydrolysis and electrical insulation. BIEGLO offers natural, colored and tribological modified PEEK with superior sliding properties and abrasion resistance. We offer a wide range of PEEK rods diameter starting at 6mm to 100mm. Our PEEK rods are also available made of compounded PEEK.

It is possible to have square as well as round shapes, drilled holes and slots from Ø2 – Ø30 mm, with counter bores and tapped holes. To reduce stress concentration and shearing stress when mounting, we recommend the reinforcement of the clamping areas by fixing glass reinforced laminate (GHGW) plates. GHGW-reinforcement plates can be purchased loose or attached to the leaf spring. A special two-component adhesive is applied for the bonding. Following images indicate possible spring shapes:

Rotary drives convert the linear movement of the pneumatic cylinders into a rotary movement. Standard rotation angles are 90° – 180° – 270° – 360°. Adjustable by 10°. Special angles are possible.

We offer structural highperformance adhesives In guaranteed quality, at stable prices and packed appropriately for transportation. Do you need advice on choosing your product or are you looking for a suitable substitution? Our application and product experts are happy to help! Our experience and deep knowledge in the area of specialty chemicals and ingredients ensures that we are well positioned to effectively support both our customers and our suppliers with product and application expertise. Please contact us for more information!

Product information "Flat bottom pouches, kraft paper black, High Barrier" HighBarrier Alu-Free flat bottom pouches kraft paper black Flat bottom pouches (box pouches) are an ideal alternative to gusseted pouches thanks to their special construction. Thanks to the built-in base, these bags are stable at the POS when filled. This bag is ideal for packing different products in different shapes. Suitable for coffee, tea, salt, pepper and much more. Kraft paper gives this bag a special look that differs from other packaging. Tear notches on both sides make it easy to open the bag again after sealing. By using our special high-barrier film, our high-barrier bags do not contain aluminum and have almost the same OTA value. Printing: Your desired motif: We print your company logo or advertising slogan in up to 12 colors on your flat-bottom bag / box-bottom bag.

Belt width: 500-1400 mm Recommended speed: max. 3.0 m/s Quick and simple exchange of wear parts Blade material: polyurethane (optional + aluminum oxide granulate)

Available as either standard Catalogue Product Range or as application specific designs. Pulley Diameters up to 2,600 mm (102”) Belt widths up to 3,500 mm (138”) Shaft diameters up to 600 mm (24”) Available in many configurations, welded and T-shaped end discs for especially demanding applications Individually designed solution with state-of-the-art design software, custom built for best performance, service life and operating economy Offers a low total life-time cost We have manufactured extra heavy duty pulleys with up to 2,600 mm (102”) diameter and 45 tonnes in weight (99,000 lb)

The type UMR tube forming machines use smart operating technology with many predefined settings that can be retrieved automatically to achieve perfect mirror-like surfaces. When producing flares with 20°-90° angles, with a clamping length of 1 x D, the machine achieves perfect sealing surfaces. Flaring up to 90° can be produced in a single cycle. Tools can be changed extremely quickly. With the appropriate tools, the machine can also close tube ends.

Our rotational technology increases the possibilities of forming on tubes with minimal expenditure on tools. All the drives are servo-electric by design and, if needed, CNC-operated. In our SRM rollforming machines, all the settings are preloaded, so there is no longer any need for costly adjustments. Different tool variants further expand the processing possibilities for chipless cutting or post-bending cutting. The machines can produce internal and external profiles and can also roll in synchronicity thanks to a special tool head (inside/outside).

individual or double post materialsaving hardwoodlayer security swords for thin materials easy to push and to swivel post placable without basement or bracing to the ground easy to shift with crane or stacker