Internal threading - Import export

K-TITE high-performance thread rolling fasteners are specially designed to lower your in-place fastening costs. K-TITE fasteners form internal threads into plain holes in ductile materials upon initial installation, which: • Eliminates the need to pre-tap the nut member • Reduces problems associated with assembling screws and bolts into pre-tapped holes, such as cross-threading

are designed for optimal joint performance with lower in-place fastening costs. Trilobular thread shape Improves and expedites thread engagement and the initial thread forming Resists loosening caused by vibrations Provides a higher uniform drive Prevents internal thread stripping

Steel trivalent blue passivated. Stainless steel electropolished or blasted. Aluminium natural tone anodised.

Hardened and ground (HRC 60 ±2). Note: The locating pins are designed to make the joining process easier. Used in combination with hardened locating bushes 02026, they enable exact, low-wear, and fast changes of the workpiece. Versions D1 = 5 and D1 = 6 do not have an internal thread. Drawing reference: Form B: cylindrical pin Form C: rhomboid pin

Handle powder-coated, fine-textured structure. Steel parts black oxidised. Note: Standard colours are: black or ruby red RAL 3003.

These systems are used especially on delicate surfaces. Due to the rubber coating occurs neither scratches nor discoloration. Moreover the slip resistance is improved thanks to rubber coating. Alternative to the standard we also offer individual solutions: » Other colours rubber coating » Rubber coating harder or softer » printable rubber coat

Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material)

Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material)

Handles cast aluminum EN AC-46200. Thrust washer plastic PA 66 GF 35-X fibreglass reinforced. Hinge pin stainless steel 1.4305. Studs and washer steel grade 5.8 or stainless steel 1.4305. Version: Handles fine structured powder-coated, black or red RAL 3003. Thrust washer black. Hinge pin bright. Studs and washer blue passivated steel or bright stainless steel. Note: Plastics are subject to creeping under load (retardation).

Tapped cylindrical pins are chiefly used in blind holes. The milled flat prevents air compression in blind holes. The tapping makes it possible to use the extractor 03328.

Handle electropolished or blasted. Thrust washer, hinge pin and screw bright. Note: The thrust washer face is lightly greased before delivery. The grease is FDA conform and is suitable for use in the foodstuff and pharmaceutical industries.

stainless steel*internal thread M 10*Ø 12 mm

stainless steel*internal thread M 10*Ø 12 mm

Self-tapping threaded inserts for making high-strength, wear-free, vibration resistant screw connections in materials with low shear strength such as aluminium and aluminium alloys, brass, bronze, cast iron, duro and thermoplastics. The threaded inserts are tapered at the bottom and have a cutting slot. By screwing in they cut their own threads inside a receiver hole. This guarantees a completely secure and firm anchoring in the host material. Internal thread D1 acc. to ISO 6H. The threaded inserts with cutting slot spring slightly inwards in the slot region in some materials. This results in a screw locking effect. If this is not desired, we recommend the threaded inserts with a cutting bore.

The course external thread of SPIROL's Self-Tapping Insert forms an internal thread within a molded or pre-drilled hole during the installation process into a plastic assembly. SPIROL Series 10 Self-Tapping Inserts are thread forming Inserts best suited for softer thermoplastics or thermosets. Self-Tapping Inserts provide the best pull-out resistance for a post-mold installed Insert, yet generally cost more than their post-mold counterparts. The external threads are designed with a thin profile to minimize induced stress in the plastic and have a relative coarse pitch to provide the maximum plastic shear surface to resist pull-out.

Flat gripper with a samarium-cobalt magnet in a steel pot. The housing increases the adhesive force of the permanent magnet. The maximum adhesive force is achieved when the entire surface is placed on a metallic surface. The flat gripper has a threaded socket with an internal thread.

Flat gripper with a neodymium magnet in a rubber-coated steel pot. The housing increases the adhesive force of the permanent magnet. The maximum adhesive force is achieved when the entire surface is placed on a metallic surface. The flat gripper has a central internal thread.

Flat gripper with a neodymium magnet in a steel pot. The housing increases the adhesive force of the permanent magnet. The maximum adhesive force is achieved when the entire surface is placed on a metallic surface. The flat gripper has a 8 mm threaded socket with an internal thread. It is characterized by a force of 140 N. The diameter is 20 mm, the total height of the flat gripper is 15 mm.

Flat gripper with a hard ferrite magnet in a steel pot. The housing increases the adhesive force of the permanent magnet. The maximum adhesive force is achieved when the entire surface is placed on a metallic surface. The flat gripper has a 10 mm threaded socket with an internal thread. It is characterized by a force of 125 N. The diameter is 40 mm, the total height is 18 mm.

Tension levers can be used for simple clamping or control operations. Where applicable, there must be enough space available so that the grip can be rotated 360°. On request: Other internal threads, reamed holes and special versions. Dimension “A” available in other lengths at extra charge.

CNC turned aluminum adapter with internal or external thread for BSP, Dash (JICUNF) or metric connections for welding.

NSPV Plain to Screwed Thread Conduit Coupling Plain to screwed adaptors is designed with one side to fit rigid conduit and the other has an internal threaded end. Rigid conduit is inserted to the plain end and the threaded end requires a male adapter to be screwed into it.

Simply as a replacement for steel! Plastic does not corrode and is much less costly than steel when ordered in large batches. Glass fibre reinforcement makes the plastic tough and loadbearing. Upon request, we can check whether your steel or stainless steel parts can be replaced by glass fibre-reinforced polyamides or polyurethanes at lower cost. Threads and internal threads are also possible, also steel inlays. It just depends on the batch size.

The above mentioned filter bars are our standard designs. Here the end pieces are not sealed tight and therefore only suitable for dry applications. Not available ex stock, manufactured on demand Alternative to the standard we also offer individual solutions: » Seal-welded model for use in liquids (e.g. water, coolant) » Other fastening options (e.g. external, internal threads and threads measured in inches) » High-quality stainless steel enclosure for use in food production » Increasing the max. operating temperature up to 350 °C » Manufacture of individual, not standardised lengths up to 2000 mm

The above mentioned filter bars are our standard designs. Here the end pieces are not sealed tight and therefore only suitable for dry applications. Not available ex stock, manufactured on demand Alternative to the standard we also offer individual solutions: » Seal-welded model for use in liquids (e.g. water, coolant) » Other fastening options (e.g. external, internal threads and threads measured in inches) » High-quality stainless steel enclosure for use in food production » Increasing the max. operating temperature up to 350 °C » Manufacture of individual, not standardised lengths up to 2000 mm