Magnetic clamps - Import export

Ball, aluminium. Magnet, neodymium. Body, steel. Holding ring, steel lined with leather. Version Anodised. Holding ring chemically nickelplated. Note The magnetic clamping balls are used to gently hold components in the optimum working position during e.g. polishing, assembling and laser welding. Swivel angles of up to 90° can be set, depending on the workpiece geometry and weight. The magnetic ball can be turned on and off using the Tgrip hex key provided.

FXL-CT table-top units are built for a maximum of 2 channels without preselection. They can be used to control magnetic chucks up to a total area of approx. 1.2m2. can be controlled. FXL-CT is designed as a table-top unit or to be attached to the machine wall by means of the magnetic feet on the back. The operation is carried out directly on the device.

Pot magnets and magnetic hooks are compact magnet systems with a single attracting surface. They have a steel, brass, stainless steel or plastic shell. The steel shell prevents dispersion of the magnetic field and increases the magnetic force of the attracting surface. The shell - or pot - also provides better corrosion and chemical resistance. The maximum operating temperature ranges from 60 to 450 °C. We supply pot magnets made of neodymium, samarium cobalt, AlNiCo and ferrite

electropermanent magnetic chuck

Holding magnet for holding or clamping ferromagnetic workpieces. The DC-excited coil achieves a holding force of up to 30,000 N when energized. When the supply voltage is switched off, the workpiece to be held falls off. The holding solenoid is maintenance-free and are characterized by a low operating current at high holding forces.

Holding magnet for holding or clamping ferromagnetic workpieces. The DC-excited coil achieves a holding force of up to 30,000 N when energized. When the supply voltage is switched off, the workpiece to be held falls off. The holding solenoid is maintenance-free and are characterized by a low operating current at high holding forces.

Holding magnet for holding or clamping ferromagnetic workpieces. The DC-excited coil achieves a holding force of up to 30,000 N when energized. When the supply voltage is switched off, the workpiece to be held falls off. The holding solenoid is maintenance-free and are characterized by a low operating current at high holding forces.

Holding magnet for holding or clamping ferromagnetic workpieces. The DC-excited coil achieves a holding force of up to 30,000 N when energized. When the supply voltage is switched off, the workpiece to be held falls off. The holding solenoid is maintenance-free and are characterized by a low operating current at high holding forces.

Holding magnet for holding or clamping ferromagnetic workpieces. The DC-excited coil achieves a holding force of up to 30,000 N when energized. When the supply voltage is switched off, the workpiece to be held falls off. The holding solenoid is maintenance-free and are characterized by a low operating current at high holding forces. The holding solenoid is available in different sizes in round, flat or square design.

Holding magnet for holding or clamping ferromagnetic workpieces. The DC-excited coil achieves a holding force of up to 30,000 N when energized. When the supply voltage is switched off, the workpiece to be held falls off. The holding solenoid is maintenance-free and are characterized by a low operating current at high holding forces. The holding solenoid is available in different sizes in round, flat or square design.

Funnel stand with two funnel holders and two reducing inserts. Space-saving design with two practical storage areas. Sturdy and stable funnel stand, resistant to chemicals, shatter-proof and with continuously variable height adjustment. The funnel stand is suitable for all funnels from 40 to 180 mm in diameter. The funnel holders can be used with reducing inserts for small funnels. The funnel stand also makes an excellent filtering stand. Thanks to an innovative magnet concept no clamping screws are necessary. The height of the funnel holder can be adjusted easily and flexibly with one hand. The laboratory stand can be flexibly adapted with corresponding accessories, for example with adjustment funnel holders or a holder for Imhoff funnels. The funnel stand can also be converted into a pipette stand.

The stand for sedimentation funnels is used to keep, hold or store Imhoff funnels safely and reliably during sedimentation. Two funnel holders ensure that Imhoff funnels will be held safely and securely and can be placed in an absolutely vertical position. Stand with two holders for sedimentation funnels, suitable for funnels 90 mm or more in diameter. Thanks to an innovative magnet concept no clamping screws are necessary. The height of the funnel holder can be adjusted easily and flexibly with one hand. With the corresponding accessory the holders for Imhoff funnels can also be replaced by holders for all-purpose funnels.

Holding magnet for holding or clamping ferromagnetic workpieces. The DC-excited coil achieves a holding force of up to 30,000 N when energized. When the supply voltage is switched off, the workpiece to be held falls off. The holding solenoid is maintenance-free and are characterized by a low operating current at high holding forces. The holding solenoid is available in different sizes in round, flat or square design.

Sheet metal handling and lifting steel plates with vacuum technology. Both magnetic and non-magnetic sheets are easily lifted. The suction pad is placed on the metal product, after which the vacuum is activated by a push on the button. Now you can lift, move, or even turn the sheet metal. Vacuum lifting is used during production, storage, internal transport, transhipment, and construction. Besides vacuum lifters for metal plates, we also design pipe handling equipment. All our designs are custom made to perfectly match the individual situation. Why choose lifting plates by vacuum? Vacuum offers unique advantages compared to other lifting methods to lift plates, such as chains, clamps, and magnets. Chains and clamps can be used to lift non-magnetic plates, such as aluminium, copper, and stainless steel. Compared to these lifting methods, vacuum offers distinct advantages: No damage to the plate, not even scratches No spacers or stoppers required Easy and fast handling Less manpower

Clamp difficult or easily deformable workpieces In daily use you are optimally equipped with the TOPlus or SPANNTOP chucks. However, there are always components that are difficult to clamp due to the contour, or that will be deformed through radial clamping. So what is required is an axial chuck, which in addition can also be set-up very fast. Clamp axially on a neodymium magnet The answer: HAINBUCH magnet module. With the magnet module you can clamp components axially on a neodymium magnet. The HAINBUCH magnet module is set-up in only 30 seconds. Your basic clamping device is already mounted. You exchange the clamping head that is included in the scope of delivery. When clamping, the magnetic clamping device is pulled onto the flat contact area of your basic clamping device.

Clamp difficult or easily deformable workpieces In daily use you are optimally equipped with the TOPlus or SPANNTOP chucks. However, there are always components that are difficult to clamp due to the contour, or that will be deformed through radial clamping. So what is required is an axial chuck, which in addition can also be set-up very fast. Clamp axially on a neodymium magnet The answer: HAINBUCH magnet module. With the magnet module you can clamp components axially on a neodymium magnet. The HAINBUCH magnet module is set-up in only 30 seconds. Your basic clamping device is already mounted. You exchange the clamping head that is included in the scope of delivery. When clamping, the magnetic clamping device is pulled onto the flat contact area of your basic clamping device.

SWR magnetic clamping brackets are switchable, precise devices that meet the highest quality requirements. Each leg can be switched separately and the holding force can be infinitely adjusted for positioning. The prismatic ground underside enables work to be carried out on flat and round material. SWR is available in the following versions: SWR 150, angular adjustment locking at 30,45,90,120,150,180° or free via locking screw. SWR 180, angle adjustment 45°-225°.

FX-C lifting magnets have a round, multipole clamping surface, designed for lifting rings, sleeves, bearing housings, flange plates and similar workpieces.The load specification is valid for full-surface mounting on workpieces which cover D inside to D outside (see table Dimensions), for workpieces with a smaller mounting surface an approximate maximum workpiece weight of 3.5 kg per cm² clamping surface can be calculated. For serial workpieces, a documented test should confirm the safety factor 3.

The MCF control units are designed to operate electro-permanent magnet modules. It is available both as a single board for installation in the customer's existing control cabinets and as an IP 54 control cabinet solution. In addition to the FXE lifting magnet modules, other electro-permanent magnet components such as magnet clamping plates or magnet clamping blocks can also be controlled with the MCF, both as a single system (ALNICO) and as a double system (ALNICO/ND). The MCF can be controlled via a machine control, radio remote control, manual pushbutton or other potential-free contacts.

MBX magnetic clamping blocks have opposite clamping sides that are activated when actuated. They are designed to clamp workpieces on steel surfaces such as machine or assembly tables. Several MBX can also be connected together via the internal hexagon of the indexing shaft to clamp longer or larger workpieces.

FXL magnetic clamping blocks are available in many sizes and designs. They can be manufactured with one or more clamping surfaces and different pole sizes. As with the FXL magnetic clamping plates, they are controlled by an FXL-C control unit; optionally with only one channel or also with several channels in order to be able to control the individual clamping surfaces of a block separately.

FXL Magnetic Clamping TechnologyThe FXL square pole technology is the result of over 20 years of experience in magnetic clamping technology and combines solutions to the most common customer requirements in the highest quality design. Magnetic poles, fed by Alnico and NDFeB magnets, are anchored in a solid, super-stiff monobloc body by means of a tool steel insert with M8 internal thread. The back of the clamping plate remains flat and can be drilled in at all points - for example, for inserting a zero-point clamping system. For this purpose, the magnet system is coated with highperformance resin in a multi-stage process, which has a high mechanical strength and ensures absolute tightness and perfect electrical insulation. FXL magnetic clamping plates can be controlled with our FXL-C control units or with almost all control units from other leading manufacturers.

Permanent magnetic chucks type PMNEO are super strong, compact plates for heavy cutting. Parts from about 30x15x6mm can be stretched with max. achievable holding forces. Good holding forces can be achieved even on rough surfaces. Optional pole blocks can be built on the PMNEO. This allows turning up the workpiece so that all sides are freely accessible, can be drilled on the magnetic clamping plate and leaves more space for accumulating chips around the component. This allows long-running HSC milling-pieces never sink into the resulting chips. The chipboard is activated via a removable hex shifter. The PMNEO magnetic clamping plate, in 48mm height, is prepared to integrate reference elements directly into the magnetic chuck, so that no additional spectrum is required underneath the magnet.

Neodymium block magnet, also known as rectangular magnet, square magnet or bar magnet, compared with disc magnet, block magnet is not as commonly used as disc magnet, but their straight line and clean edge offer a pleasing and different visual appearance, what's more, it provides a bigger surface area than disc magnet of same diameter. Block magnet is usually magnetized with north and south pole on opposite square faces, also a multi poles magnetized block is possible with a new magnetizer machine. Block magnet is widely favoured for clamping applications, magnetic sweeper applications, magnetic separators in the food industry, wind turbine generators, flow control systems & water conditioning application and other related industrial applications.

The Sanitary Electromagnetic Flowmeter is also called hygienic magnetic flow meter and tri-clamp magnetic flow meter. It is a food grade flow mter and ideal for food, beverages, beer, milk and pharmaceutical industries. Sanitary flow meter can meet the hygienic demand and achieve accurate and reliable flow measurement.

Magnetic clamping technology from AMF: safe, reliable and efficient. This innovative technology is based on the force of the magnetic field. This opens up new possibilities that make all surfaces fully accessible for the machining of a workpiece even at constant tension.

We have a large stock range of product consumables, including – Plastic Jogger Blocks, Magnetic Clamp Pads, Plastic Knife Guard Book Back Cutters, Frazing Knives, Cutting Sticks, Paper Drills, Stitching Wire, Feeder Suckers and Silicone Spray. Please get in touch for a full price list.

With its unique ergonomic features and ease of use, the device is ideal for mobile use. The scribe marking system type 317 is available with different handles for flexible adaptation and handling. Being a lightweight of 5.5 kg (without controller, pneumatic and chuck), the unit sets new standards. It offers a large marking area of 120 mm x 25 mm at its small dimensions. Via quick interchangeable, optional fixtures it is possible to adopt to virtually any vehicle geometries. The compact controller provides extensive opportunities for data input via PC, barcode scanner, PLC or the integrated keypad. By this keypad the easy creation and selection of the model-dependent imprinting orders is provided. Options • Vehicle-related fixtures with manual, pneumatic or magnetic clamp functionality

All series are available with or without handlebar grip and with or without additional holes to accommodate angles. The usage possibilities of the standard magnets can be extended individually through accessories such as longitudinal or frontal suppressing or clamping adapters. — Magnetic rubber (series A) or neodymium magnets (series P and PDA) — Temperature exposure up to 60 °C, series P and PDA on request up to 80 °C — Eccentric removable — Smooth surfaces, easy to clean