Small%20metal%20parts - Import export

Unshielded system. The magnets can be mounted by pressfit or gluing. 1) magnetic face

Hardened to 780 ±40 HV 10 and ground. Without leadin groove. Note All bushes have the bore size marked on the upper face, e.g. 10. Diameters D1 over 15 mm increase in size by 0.5 mm. Dowels or coiled spring pins together with DIN 1731 flathead screws can be used in place of the stop pin.

From diameter D1 over 15 mm size increases are 0.5 mm.

From diameter D1 over 15 mm size increases are 0.5 mm. 1) Chamfer for insert

Housing thermoplastic. Version: Operating principle: Magnetic. Rating: IP67. Note: If the actuator is within the switching range (safety door closed), the safety contacts and, if applicable, the signal contacts of the safety switch are activated. The contact is thus closed via a magnet (magnetic field). Form A: Actuator on one level to the safety switch. Form B: Actuator offset by 90° to the safety switch.

Housing Form A plastic. Housing Form B die-cast zinc alloy. Active face POM. Housing Form C high-alloy stainless steel Version: Voltage: U = 10 – 30 V DC Function: Normally open Switch type: PNP Mounting type: flush Security type: IP 67 Note: Non-contact, functions wear-free with high switching frequency and accuracy. Non-sensitive to vibrations, dust and moisture. Inductive sensors record all metals without contact. Form C enables screw fastening in a T-slot. Is safe and saves space as the proximity switch lays flush in the slot. Short-circuit proof and reverse-polarity protected.

Single-phase primary switched-mode power supply in metal housing. Note: Closed version with screw fittings with contact protection. Overload protection due to current limit, auto recovery. Protected against short-circuit, overload and surges. Power on LED indicator. For DIN top hat rail mounting. Technical data: Rating: IP00 Protection class: I Standard: UL508, TUV EN60950-1, CE Connection: screw terminals with contact protection Fastening: installation on DIN rail TS-35/7.5 or 15

Polyamide fibreglass reinforced. Version: Black. Note for ordering: The connecting elements are supplied in pairs. Note: The connecting elements are used to attach the two ends of the energy supply chain to the installation. Tension relief is integrated into the connecting element. The connecting elements are connected on the outer radius.

Polyamide fibreglass reinforced. Version: Black. Closed. Note: Energy supply chains for safe guiding of flexible electric and data cables as well as pneumatic and hydraulic hoses. The modularly constructed chains can be easily shortened or extended. The material is UV-resistant and therefore also suitable for outdoor applications. Technical data: Technical features in unsupported areas: Speed: 10 m/s Acceleration: 50 m/s²

Cable and housing PUR Contacts gold-plated bronze. Version: Bush (female) Voltage: U max. 60 V Current: I max. 4 A Terminals: 3-pin Security type: IP 67 Note: Plug connector with screw fitting. Plug encapsulated to cable.

Housing, plastic Contacts M8x1 gold-plated bronze. Contacts M12x1 Optaloy-coated brass. Version: Bush (female) Voltage: U max. 60 V Current: I max. 4 A Terminals: 3-pin (4-pin by M12x1) Security type: IP 67 Note: Plug connector for self-assembly with screw lock.

Mounting plate steel/plastic. Monitor bracket aluminium. Bearing washers and sleeves plastic. Mounting flange aluminium. Mounting adapter aluminium. Screws steel. Version: Mounting plate painted. Monitor bracket painted. Mounting flange painted. Mounting adapter painted. Screws electro zinc-plated

High-strength material mix of thermoplastic/aluminium. Version: Black/bright. Note: We offer three different basic brackets for industrial monitors and touch panels: Compact: space-saving, with a swivel range of 60°. For loads up to 10 kg (static). With universal mounting plate. The basic bracket is suitable for mounting on tubes size Ø30 mm or 30x30 mm. By using the optional reducer sleeve 29040 they can also be mounted on other sized tubes (Ø20 and Ø25 mm or 20x20 and 25x25 mm). With rotary flange: vibration-resistant, lockable monitor bracket with an angle adjustment of 90° in 15° increments. For monitors / control units up to 25 kg (static). With universal mounting plate. The basic bracket is suitable for mounting on tubes size Ø30 mm. By using the optional reducer sleeve 29042 they can also be mounted on other sized tubes (Ø20 and Ø25 mm or 20x20 mm).

Steel 1.0037. Aluminium EN AW-6060. Version: Steel electro zinc-plated. Aluminium anodised. Note: The machined tolerances of these round and square tubes are individually matched to the tube clamping system. *Square aluminium size 10x10 are only available as solid bars. On request: - Custom cut length (L max. 5000 mm) - Stainless steel tube (L max. 3000 mm)

Investment cast 1.4308 stainless steel. ISO 4762 cap screw and ISO 4032 hex nut, stainless steel. From ø30 mm ISO 4017 hex head bolt, stainless steel. Version: Electropolished. Note: The tube clamps with diameters 30 and 40 mm have a silicone sleeve that protects the thread of the hex head screw from contamination and damage. On request: Clamping levers for tightening. Accessory: - Round and square tubes 29050

Thermoplastic. DIN 7984 screws and DIN 985 nuts steel. Version: Black. Screws and nuts electro zinc-plated. Note: The standard size for round tubes is Ø18 mm or Ø30 mm. Use reducer sleeves 29042 if smaller tubes are to be clamped or a conversion from round to square tubes is required. On request: Plastic levers for locking. Accessory: - Reducer sleeves 29042 - Round and square tubes 29050

Material, version: 1. Sealing cap red Polyamide 66 thermoplastic. 2. Filler sieve black Polypropylene thermoplastic. 3 Flange electro zinc-plated steel. 4. Fastening screws electro zinc-plated steel. 5 Flange seal cork. 6. Chain brass.

Housing fibreglass reinforced thermoplastic polyamide. Sight glass thermoplastic polyamide. O-ring and flat seal NBR. Reflector PVC. Float plastic. Screw and nut, steel. Version: Housing black. Sight glass crystal clear, high mechanical stability, non-ageing. Reflector white. Float red, with magnetic element. Screw and nut electro zinc-plated. Note: The oil level gauge not only enables the oil level to be viewed but also recorded using a REED switch. In addition, the oil level gauges can also emit an electric signal if the temperature of the liquid inside the container reaches the threshold of 70 °C. As soon as the float element approaches the selected minimum value after the circuit has been closed, the system emits an electric signal. The sensor is located on the housing and its height can be adjusted in line with the control requirements for the oil level. The minimum level is ca. 35 mm from the centre of the lower fastening screw.

Housing, die-cast zinc. Housing cover, plastic, self-extinguishing. Hinge bolts, die-cast zinc/steel C45. Contacts, silver-nickel alloy 10. Note: The security hinge switches are used for monitoring the position of swing-hinged safety doors, protective hatches and hoods. The protective device is monitored directly in the hinge. By the universally pre-set versions, the switching angle is freely adjustable over the entire working range. A mounting aid ensures the quick alignment to doors and posts. The additional hinges have the same appearance and dimensions as the security hinge switches. The loading values given for the hinges are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties.

Housing steel. Viewing glass thermoplastic polyamide. O-ring and flat seal rubber (NBR). Reflector aluminium. Screw and hex nut steel. Version: Housing painted black. Transparent viewing glass, high mechanical stability, non-ageing, temperature resistant with oil up to 100 °C, with water up to 70 °C. Reflector painted white, markings and scale black. Screw and hexagon nut, electro zinc-plated. Note: The oil level gauges can either be fastened as shown in the illustration or directly in the threaded hole. Centre distance for the fastening holes = L1 ±0.5. The oil level gauges are suitable for tanks operating without pressure. Maximum operating temperature: 100 °C.

Aluminium 6060 T5. Cover plug PA 6.6. Version: Black anodised. Colourless anodised. Note: These hinges have stainless steel tension springs which enables doors and hatches to open or close automatically. Opening angle 270°. Spring torque opening: M(0°): 0.7 Nm / M(90°): 0.5 Nm / M(180°): 0.3 Nm Fastened with DIN 7991 countersunk screws.

Steel. Stainless steel 1.4305. Stainless steel A4 1.4401. Version: Steel electro zinc-plated. Stainless steel bright. Note: Block hinges with fastening nuts and extended middle section for inset doors. Mounted with nuts (M6 or M8) from inside. The hinge can be mounted left or right. The opening angle is 180°. Supplied unassembled. Fastening nuts and washers are supplied.

Stainless steel 1.4404. Version: Satin finished. Note: The hinges are made of weldable profile steel. The pin is fixed into the lower part of the hinge. The differing steel qualities of the weld and the beam onto which the hinge is welded must be at least equal to or better than: Stainless steel 1.4404

Steel, pins and connecting elements 1.4016 stainless steel. Stainless steel, all components 1.4404 stainless steel. Version: Electro zinc-plated. Bright. Assembly: - For recessed or surface mounting. - Can be mounted on right or left side. - For horizontal or vertical applications. Drawing reference: 1) recessed mounting 2) surface mounting

Hinge and caps fibreglass reinforced PA thermoplastic. Hinge pin stainless steel. Version: Hinge and caps black. Pin bright. Note: These hinges have a detent mechanism. This mechanism holds a door or lid open at three different angles or tightly closed. The hinges are available with or without guide tabs for aluminium profile slots. The loading values given for the hinges are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties.

Fibreglass reinforced thermoplastic. Hinge pin stainless steel. Version: Hinge black. Pin bright. Note: All hinges can be supplied on request with guide tabs for the slots of aluminium profiles (slots 6, 8 and 10). They facilitate assembly, secure the hinge against rotation and make it harder wearing. The loading values given for the hinges are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties. The load values have been determined under laboratory conditions. Each user must determine individually whether the hinge is suitable for the respective application. Different materials onto which the hinges are installed and the type of mounting, weather conditions and wear can influence the determined values.

Steel or 1.4305 stainless steel Version: Steel trivalent blue passivated. Stainless steel, bright. Note: Swivel feet consist of a threaded spindle and a plate joined together. Any threaded spindle can be combined with any plate. The height of the complete swivel foot can be calculated from the length of the threaded spindle + height of hexagon + 22.5 mm. (Overall height of swivel foot = L + L1 + 22.5 mm) Depending on the version, threaded spindles can have a thread undercut in front of the hexagon.

Plate die-cast zinc or stainless steel 1.4305. Anti-slip plate thermoplastic elastomer. Version: Die-cast zinc plate, black powder-coated. Stainless steel plate, bright. Note: Swivel feet consist of a plate and a threaded spindle or ball joint. Any plate can be combined with any threaded spindle or ball joint. The anti-slip plate absorbs vibrations and prevents the swivel foot slipping. For matching threaded spindles see 27810. For matching ball joints see 27811.