Wire devices - Import export

For transmission and distribution of electric power at stationary devices with rated voltage 0,660kV and 1 kV frequency 50Hz. For stretching in the air where there is no danger of mechanical damage of the cable, also for laying into channels without influence of stretching forces. While laying the cables in a single layer, they are flame retardantThe copper cores with section 2,5-25mm2 inclusive are produced of single wire of 1 class flexibility, accorgind to gost standard 22483-2012. Number of cores in the cable 2,3.in case of supply in bundles the construction length is agreed with the customer. On wooden drum no less than 450m. One batch can contain no more than 20% of cable length not less than 50m.

Testing requirements for a manufacturer in electronics industries had changed: For an assembly included in a smartphone, the absence of contact between speaker ultra fine wires and adjacent components is essential. Fulfillment of this condition, until now only subjected random sampling by microscopy, from now on has to be verified in a 100% procedure. Due to labor cost, microscopy for this amount of inspection is no more lucrative. Detection of ultra fine wires in electronic device The particular challenge The fine wires made of copper in smartphone speakers dispose of a high reflection and only a small diameter. The QuellTech Solution A high-resolution QuellTech 2D/3D Q4-5 Laser, featuring a particularly adapted laser wavelength and an ultrafine laser line in the corresponding installation, is combined with a linear axis equipped with a convenient encoder output. Due to its special chip analysis, the Quelltech sensor delivers a stable and highly reproducible signal on the fine wires

Hubbell offer very secure connection systems for hight and medium current. Switching boxes for hight and medium loads and currents. The connection materials from HUBBELL wiring-Devices are matching the safety standarts of NEMA and OSHA. The connection system is covering a wide range of connectors, You do have the STRAIGHT BLADE range of connectors as the Safety TWIST-LOCK as a HUBBELL-LOCK range and a Circuit-lock. The classification of the connectors is done regarding the load and the current they can carry and the polarization is depending from those features. some connectors can carry up to 600 Amp

Stainless steel maine connectors from HUBBELL suit all marine purposes. Shore side Power Inlets Boat side Power Outlets Moulded cable assemblies,various lenght. Carrying up to 100 Amp Very resistant mechanical and electrical propreties. Data communication connectors USB, and TV plugs can be integrated. Approvals and widely used over the all world in the harbours.

Today, electrical and wired devices are the most needed products. Computers, televisions, internet, chargers or many machines are used wired. In order for the cables to have a long service life and be used without problems, they must be very well maintained. For this, there are also cable regulators. These regulators prevent and protect the cable from damage. In this way, there are no situations such as breaking, breaking, crushing or bending. It is one of the most preferred materials.

The RESISTOMAT® model 2320 is a universally applicable and easy to operate measurement device for low-ohmic resistances. The light and handy device in a stable IP54 plastic housing with membrane keypad is likewise suitable for use in service, laboratory or on the production floor. The power supply is done via built-in rechargeable battery packs or by standard batteries. If need be, the temperature of samples can be measured and the sample resistance is subsequently compensated to fit the value at 20°C. This applies for samples with resistances depending on the sample’s temperature. The temperature coefficients for copper and aluminium are included as standard. A third and fourth coefficient may be set individually for any given material to be measured. Features: — Measuring ranges from 40 mΩ to 4 kΩ — Resolution up to 10 μΩ — Measuring accuracy 0.05 % Rdg. — Autorange — Temperature compensation — Bipolar measurement — Input voltage protection up to 415 Vrms

The model K 26 is a robust stud welding gun, especially for studs ø 22 – 25 mm Ideal for welding shear connectors SD 25 mm Ideal for through-deck-welding td Most suitable for long shear studs Adjustable hydraulic plunge damper Standard support with 3 legs Body: fibre-glass reinforced polyamide Lifting ring system with length compensation up to 8mm Control cable plug (4 wire) Optimal Integrated shielding gas device

The model SK15 is a robust stud welding gun, designed for welding of threaded studs with ceramic ferrules ø 4 - 12 mm Ideal for short cylce stud welding ø 3 - 12 mm Best for stud welding using shielding gas ø 3 – 12 mm Lifting range 1 – 4,5 mm Standard support with 2 legs High repeatability Body made of fibre-glass reinforced polyamide Control cable plug (4 wire) Optional Integrated shielding gas device

Bus Bar Working Stations for Bus Bars and Flat Material Punching Tools for Bus Bars and Flat Material Cutting Tools for Bus Bars and Flat Material Bending Tools for Bus Bars and Flat Material Brochure Tools for Control and Switchgear Cabinets Tools for Laminated and Flexible Bars and Earthground Sheet Metall Hole Puncher DIN Mounting Rail Cutting Devices Wiring Duct Cutting Tool Punching Tools for Sheat Metall

Retractable Power Distributor/power bollard SV501 for indoor and outdoor use, made of saltwater-resistant aluminum. Due to its solid construction, the SV501 lowering distributor can be driven over by a truck, of course, only when the lid is fully closed. The surface is anodized with a stainless steel look. The retractable power distributor SV501 is equipped with 8 protective contact sockets 2 / 16A 230V with hinged cover (unsecured, without wiring). The devices are raised and lowered using a crank. Drainage is required for outdoor installation. The housing is watertight when closed, protection class IP67. Alternatively, other combinations are also possible. Further equipment variants and colors on request.

Universal Testing Machine is a representative test equipment for physical properties. It is capable of measuring load, strength, elongation of products or materials such as rubber, film, plastic, metal, etc. - Frame Load Capacity (Max.) : 5kN - Main Load Cell : 5kN - Load Range : 50 (kgf) ◀(Up to 4-step conversion) - Column Type : Single Column - Load Accurancy : Less than ±0.5% - Crosshead Speed Range : 0.01 ~ 500mm/min - Load Resolution : 1/50,000 - Machine Controller : Touch Type Servo Controller(Position Control Type) - Test Category : Tensile, Tear, Peel, Compression, Bending, Repeat, etc. - Dimensions : 478× 650× 1375(H), 82kg - Main Power : AC 220V 2P, 50/60 - It is single column model that can be tested under 5kN. - UNITEST M1 is widely used for testing materials such as films, rubber, fibers, medical devices, biomaterial, and wires etc. - The main feature of the UNITEST M1 is that it requires a small footprint

Argon welding is the word “Tungsten Inert Gas” that gives the welding method its name. Welding is also called the initials of this word and is referred to as TIG welding. The heat to perform the welding process is generated between the electrodes made of tungsten metal, which has a very high melting point, and the parts to be welded. The welding zone is protected by argon or helium gas sent from a nozzle surrounding the electrode. The electrodes used in the Tig (argon) welding method allow to join the welded material by melting, without melting themselves. When deemed necessary, additional welding rods are delivered to the welding area by the welder or by automatic wire feeding devices, as in oxy gas welding. Argon gas is generally used as a shield in argon welding. Argon gas is a noble gas, so it does not react and provides strong protection. It optimizes the ignition characteristics and stability of the arc

Stirrup bender and bar shaping machine from coil with 2 bending heads for the production of stirrups and shaped wires with bends at both ends using wires up to Ø 16 mm (#5). Driven by electric servomotors. Also available HS version machine. These automatic stirrup benders and bar shaping machines are equipped with Max. pulling speed 140 m/min (460 ft/min) HS Version 200 m/min (660 ft/min) Straighteners (horizontalvertical) with electronic and independent setting for the 2 wires with Joystick AntiTwist electronic device (Optional) Patented feed unit that allows independent advancement for single o double wire (Optional) 2 bending unit (upper and lower) 4 pulling drive wheels Cutting unit with adjustable wire guide, reversible mobile and fixed cutting blades Web Teleassistance 3D version for the production of tridimensional pieces.

Stirrup bender and bar shaping machine from coil with 2 bending heads for the production of stirrups and shaped wires with bends at both ends using wires up to Ø 20 mm (#6). Driven by electric servomotors. These automatic stirrup benders and bar shaping machines are equipped with Max. pulling speed 140 m/min (460 ft/min) Straighteners (horizontalvertical) with electronic and independent setting for the 2 wires with Joystick AntiTwist electronic device (Optional) Patented feed unit that allows independent advancement for single o double wire (Optional) 2 bending unit (upper and lower) Pulling with 4 motors and 4 pulling drive wheels Cutting unit with adjustable wire guide, reversible mobile and fixed cutting blades Web Teleassistance Prestraightening Feeding Unit (Optional) Automatic motorized wire change (Optional) 3D version for the production of tridimensional pieces.

Bidirectional automatic stirrup bender from coil for the production of stirrups and cuttosize bars using wires up to Ø 20 mm (#6). Driven by digital electric servomotors. Coil 20 automatic stirrup benders are equipped with Max. pulling speed 140 m/min (460 ft/min) Straighteners (horizontalsverticals) with electronic and independent adjustment for the 2 wires with Joystick AntiTwist electronic device (Optional) Pulling with 4 motors and 4 pulling drive wheels Cutting unit with adjustable wire guide, reversible mobile and fixed cutting blades Web Teleassistance

Bidirectional automatic stirrup bender from coil with disk bending system for the production of stirrups and cuttosize bars using wires up to Ø 14 mm (#4). Driven by electric servomotors. Formula Disk automatic stirrup benders are equipped with Max. pulling speed 200 m/min (660 ft/min); Straighteners (horizontalsverticals) with electronic adjustment and independent position for the 2 wires with Joystick; AntiTwist device (Optional); Cutting with Brushless motors; Web Teleassistance.

Bidirectional automatic stirrup bender from coil for the production of stirrups and cuttosize bars using wires up to Ø 14 mm (#4). Driven by digital electric servomotors. Formula 14 stirrup benders are equipped with Max. pulling speed 150 m/min (500 ft/min) Straighteners (horizontalsverticals) with electronic adjustment and independent position for the 2 wires with Joystick AntiTwist device (Optional) Cutting with Brushless motors Web Teleassistance

Powerful audible alarm (103 dB @ 1m) Run time of up to 170 hours More than 4-month datalogging capacity Easily transportable - less than 7 kilos 2.4 GHz frequency 30 Devices per network MX 40 Up to 32 Devices, Wired or Wireless Up to 16 BM 25 Configurable up to eight zones Alarm and Fault Condition LEDs Rent the BM 25 & MX 40!

The RBK 60 S is an extremely robust water-cooled weld head for a standard heat exchanger application up to an ID of 60 mm, modified to an ID of 99 mm or 120 mm. The head is pneumatically centred and is available with a rotating wire device and/ or arc voltage control (AVC) as an option. The head can also be used with a pneumatic positioner instead of a balancer. Versions: — RBK 60 S weld head with pneumatic centring, including hose package, 8m, water-cooled — RBK 60 S weld head with pneumatic centring and wire feeder incl. hose package, 8m, water-cooled — RBK 60 S weld head with pneumatic centring, wire feeder and AVC incl. hose package, 8m, water-cooled Package includes: — Weld head — Small torch incl. torch consumables and tungsten electrode Ø 2.4 mm — Water-cooled hose package, 8 m — Pull bar B — Transport case Optional: — Div. spring sleeves and pull bar sets for RBK 60 S — Torches, Balancer, Tube-to-tubesheet positioner...

FC-7668 is a intelligent alarm control system which in tegrated with burglar proof, fireproof, gas leak proof. It is compatible with wired and wireless alarm mode. It uses advanced coding techniques of BUS zone and multi-bit random code hopping techniques in security and reliability. to avoid false alarm and interference effectively. adopt SMS, 2G/4G, high-speed Contact ID alarm transmission mode. this system is widely used in residence community, villa, shops, offices. ◎ Chinese&English operation menu and voice prompt. ◎ 8 tamper-checking wired zone,32 wireless zone,88 BUS zone(with tamper-checking single zone module) ◎ 8 programmable access wireless remote, 8 programmable access keypad, 32 wireless appliance switch,8 wireless siren. ◎ Support SD card update application software. ◎ Support 2G/4G, TCP/IP, networking alarm setting. https://vedardalarm.com/commercial-security-wired-wiress-bus-zone-alarm-panel-p-264

This fire alarm control panel meets NFPA requirement. It should be installed, commissioned and maintained by suitably qualified service personnel. Description: 1. It has 16 zones and 4 sounder outputs. 2. It has 3 standard FORM-A relays contact for alarm, fault, supervisory. And it has EIA-485 port for communication with remote delay and repeater panel. 3. It works with conventional N/O contact input devices including 2 wire, 4 wire smoke detector, heat detector, gas detector and call points etc. 4. It can be programmed by panel keypad. It is supervised all wiring, AC voltage and battery level. 5. It is required to be connected to power earth and it self checks earth fault. 6. Max.20 detectors can be equipped in one zone. Each zone can be disabled separately. 7. Output circuits: 24V resettable power output 1000mA 24V Nonresettable power output 1000mA 24V battery charger (up to 18AH battery) https://vedardalarm.

The LSP-TSTS is a slim design easy to use temperature transmitter for Pt100/Pt1000 3 wire or 2 wire temperature sensor. This device provides a linearised 4-20mA signal output, proportional to the temperature characteristic of the Pt100 or Pt1000 sensor. Temperature range can be changed on request before order (Default -15 to 150ºC). Features • RTD type Pt100 or Pt1000 Input • 4 to 20 mA linearised output on current loop or 0-10V • TS-35 DIN rail mounting • +/-0.1% accuracy • Ip40 case • Screw terminals • Easy to use • Supply from current loop

The measuring probe lance is in the form of a length of 2000 mm and includes the three temperature sensors: - on the tip of the lance - at a distance of 750 mm from the tip and - at a distance of 500 mm from the end of the lance The lance tip has a rounded head, so when pushing into the pile it does not poke through encountered "in the way" compost components. The probe in wireless version is powered by a battery. Measurements and data are transmitted, depending on the version of the device, by wire or wireless.

The measuring probe is in the form of a lance 1000 mm long and contains an oxygen sensor. The end of the lance driven into the compost has a rounded head, so that the compost components encountered "on the way" do not stick into it. The probe is powered by direct current with a rated voltage of 12VDC or 24VDC, while the data on measurements are transmitted, depending on the version of the device, by wired or wireless. The oxygen probe in the version with wireless data transmission can be equipped with two network interfaces depending on the demand. In the wired version, the data signal is realized in the analog 4-20mA or digital form via the CAN bus. The second solution is to transfer data directly to the cloud via the LoRa network. This type of transmission allows you to cover a huge area with a radius of several kilometers in a star topology with one base station or through the public network.

Promag H is the preferred sensor for applications with highest requirements in the food and beverage and life science industries. Promag H 200 offers in addition genuine, industry-compliant two-wire technology. This enables the device to be seamlessly integrated into existing infrastructures and control systems. Additional advantages are high operational safety in hazardous areas thanks to an intrinsically safe design (Ex ia), and a familiar installation procedure.

This pressure transmitter is particularly well suited for monitoring filters and pressures in HVAC (heating, ventilation and air conditioning) applications. DIP switches allow users to configure the output signal and switchable measurement ranges (optional). Settings provide an option for conversion to a root-extracted output signal (displayed as a % of the maximum output value). An internal button is also available for performing a zero-point correction or fine-tuning the end value. An optional display allows users to read the measured value directly on site in Pa or kPa. With an optional time constant (up to 10s), the instrument can produce an attenuated output signal, even under unstable pressure conditions. An optional two-wire version of the device is also available for reducing wiring complexity. In addition to simple wall-mounting with just 2 screws, the PS 17 is also suitable for mounting on top-hat rails.

Promag P 200 offers genuine, industry-compliant two-wire technology. This enables the device to be seamlessly integrated into existing infrastructures and control systems. Additional advantages are high operational safety in hazardous areas thanks to an intrinsically safe design, and a familiar installation procedure. Promag P 200 is dedicated for chemical and process applications with corrosive liquids and high medium temperatures.

The Round Solutions PingPong is an embedded IoT/M2M hardware platform made for Software Developers. The platform supports extension boards that add unlimited capabilities. It can be used to easily make physical devices that connect to the web. It's literally plug, push and play. PingPong comes with both wired and wireless connectivity. The device is available in two open-source SW versions. While the RTOS version comes with the world's fastest 32-bit microcontroller running in C/C++, the Linux version uses the powerful ARM Cortex processor for even more functionality and applications. PingPong base circuit boards also have a high speed Telit cellular module, a high accuracy positioning component for the Global Navigation Satellite System (GNSS), Ethernet, USB, CANBUS among other items. The Evaluation Kit comes with a dedicated M2M/IoT SIM card and connectivity to a cloud platform.

TYP C 060 Cutting and forming Device for jumper wires Description The Streckfuss model C060 is designed to cut and form 20 to 22 gauge jumper wires. The machine has an adjustable center to center distance and uses interchangeable die sets to vary the cut length. The wire straightener, feed clamp and backlash assembly combined with an adjustable feed stroke produce a precise jumper wire every time. Components